Question No. 04 (CLO-3). A compound shaft consisting of a bronze segment and an aluminum segment is acted upon by two torques as shown in figure 2. Solve to determine the uniform shaft diameter subject to the following conditions: Thr < 80 MPa, tal < 55 MPa and the angle of rotation of the free end is limited to 6°. For Bronze, G 35 GPa and for aluminum, G = 28 GPa. 950N-m 700N-m Bronze Aluminun 900mm 600mm Figure 2: Question No. 4

Question No. 04 (CLO-3). A compound shaft consisting of a bronze segment and an aluminum segment is acted upon by two torques as shown in figure 2. Solve to determine the uniform shaft diameter subject to the following conditions: Thr < 80 MPa, tal < 55 MPa and the angle of rotation of the free end is limited to 6°. For Bronze, G 35 GPa and for aluminum, G = 28 GPa. 950N-m 700N-m Bronze Aluminun 900mm 600mm Figure 2: Question No. 4

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Civil Engineering 2. For the following schedule, draw the anode network, perform the CPM calculations, mark the critical path, and complete the table entries Activity Duration IPA Lag ES EF LS LF TF FF В, С 3. F.G IPA: Immediately preceding activity H. 3 4664 426 ABCD EFG
i need the answer quickly
Give me right solution according to the question.
I need a quick solution within 15 minutes With my best wishesTon.
I need the answer as soon as possible
Equipment A: The cost of equipment A is $100/ Hr The volume per cycle is 4 CY / cycle The cycle time is 10 minutes The equipment works 50 min / Hr Equipment B: • The cost of equipment A is $110/ Hr The volume per cycle is 6 CY / cycle The cycle time is 12.5 minutes • The equipment works 50 min / Hr Which Equipment option has lower $ Cost per CY ?
criteria Speed mile hr Distance mile Accident # cost ล 20 5 15 0 Altrantive 1- 40 6 1.5 2 30 3 3 0.8 Three altrene tives routes begin at location A and end at loration B Table below Shows. the criteria for each all Determine the measures of effectives for each. © Evalute the alteratives based on a for for your paint one. 3) What could be the afferative, most likely to be selected al view? given criterion.
How is gravity filtration different from vacuum filtration?
Hazen-Williams formula was used in the derivation. 2- Explain why the Aluminum sulfate (alum) is widely used as a c 1-What are the factors allecting coagulation. b-Prove that the value of the exponent x in the relation (h=kQ) is 1.85 when Q5: distinguish its occurrence? a-Explain why cavitation oecurred in pumps and how one can icoagulant.
Assuming that the specific gravity of the following substances is approximately the same, that is, 2.65, and that the water is at 20°C, calculate the time it will take to settle 1m of the following materials: a) Gravel (Dp=10,000 μm) in seconds I want help with this one, I did the problem but the time gave me 36.36 seconds and the Dr told me that the result is incorrect, I would like to know how to do it. I used the formula of V=Dp^2(g)(△p) / 18μ ; Then use a substitution to calculate the time which would be t=h/v
Hydraulic machine
(Same given conditions as the previous problem) Convert one hr UH to 2 hr UH. What is the value of "C" in the table? time (hr) 0 0.5 1 1.5 2 2.5 3 3.5 1-hr UH, cfs 0 32 44 52 36 22 10 O 2-hr UH, cfs 0 A B CO С