Pipe in Parallel:Two pipes connect two reservoirs which a height difference of 10m. Pipe 1has diameter 50mm and length 100m. Pipe 2 has diameter 100mm andlength 100m. Take f= 0.008 then calculate: -a) Rate of flow for each pipe.b) The diameter D of a pipe 100m long that could replace the two pipeand provide the same flow.energy lineH. h

Answered: Image /qna-images/answer/ff673c71-9bca-46de-af23-1cc539a3016e.jpg

Answered: Pipe in Parallel: Two pipes connect two…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

From the following figure, determine: a) the flow rate through the pipe b) the velocity in the pipe c) the pressure at points A, B, C, D. d) outline the line of motor head for this situation . fluid is
Water at a rate of 60 GPM flows in a 3 inch-diameter pipe at 100 psia and 150 F. Find a) the volumetric flow rate, b) mass flow rate, c) mass flux, and d) flow velocity. Note: At P = 100 psia and T = 150 F: v = 0.01634 ft3/lb
Q12
No. 1: A water system of 2 inches (inside diameter) pipe, having a length of 1/4mile, is to be flushed with a volume of water equal to twice that contained in the system. How much water (number of gallons) must be flushed through the system. (1??3 = 7.481 ???????)
A 140 m long pipeline runs between two reservoirs, both ends being under water, and the intake end is square-edged and non-projecting. The difference between the water levels in the two reservoirs is 40m. a) What is the discharge if the pipe diameter is 20 cm and f = 0.007? The density of water may be taken as 1000 kg/m³. b) When this same pipe is old, assume that corrosion reduces the diameter to 18 cm and that f becomes 0.012. What will the rate of discharge be then?
Please solve what is ask with complete handwritten solution, Thank you so much!
An industrial process requires water to be pumped from one tank to another. The extraction point is 6.0 m below the delivery point, and the total run of pipe is 50 m. The pipe connecting the two tanks is a 5 inch nominal diameter schedule 40 steel pipe. You may ignore minor losses. Two different suppliers offer you pumps A and B (their performance curves are shown above). a) Which pump will you selectb) Motivate your selection in (a)c) Determine the volume flow rate in m3/h d) What is the power consumption (in kW) of the motor required to drive this pump (you may ignore the reactive power of the motor)
Q2: The motion speed of the piston in one hydraulic transmission system is depend on the inlet flow rate, if gw=50ml/s, the surface of the cylinder is 5 cm², so what's the speed of the piston?
... P1 = 50 KPa P2 = 10 KPa 4m OIL 1.6m OIL In the figure, an orifice is locates in the partition wall so that it discharges oil (SG = 0.8) from left to right side of the room. The orifice %3D has a diameter of 100mm and is under the surface of oil, 4m from the surface on the left and 1.6m from the surface on the right. The surface at the left is under 50KPA of pressure and the surface at the right side is under 1OKPA of pressure. Determine the actual discharge in the orifice if C = 0.92 112.03 L/s B 87.63 L/s 95.25 L/s 103.07 L/s No Answer among the choices
Water flows through a circular pipe with a radius of 15 cm at a rate of 1.5m/s into astorage tank. A) Calculate the mass flow rate, b) Calculate the mass of water that willflow into the storage tank in 10 minutes. C) How long will it take for 250,000 kg of waterto enter into the storage tank?
The rate of flow of water through a horizontal pipe is 271 lit/s. The area of the pipe suddenly enlarges from 300 cm2 to 1200 cm2. The pressure intensity in the smaller pipe is 11 N/cm2. Determine:a) Loss of head due to sudden enlargementb) Pressure intensity in the larger pipec) Power lost due to enlargement
Please complete it till 5 pm pakistan time

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS