A) There is a permeable filter system where the pressures on Side 1 and Side 2 are 28 mmHg and 52 mmHg, respectively. Assume a hydraulic conductance of 4.0 x 10-6 cm/Pa-s and total area of 2.0 m² for the membrane. Which direction will the fluid flow and at what rate? B) Now assume the above is semi-permeable and the osmotic pressure on Side 2 is 27 mmHg. What would the osmotic pressure on Side 1 need to be for the flow to be reversed?

A) There is a permeable filter system where the pressures on Side 1 and Side 2 are 28 mmHg and 52 mmHg, respectively. Assume a hydraulic conductance of 4.0 x 10-6 cm/Pa-s and total area of 2.0 m² for the membrane. Which direction will the fluid flow and at what rate? B) Now assume the above is semi-permeable and the osmotic pressure on Side 2 is 27 mmHg. What would the osmotic pressure on Side 1 need to be for the flow to be reversed?

Name: A) There is a permeable filter system where the pressures on Side 1an
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A) There is a permeable filter system where the pressures on Side 1and Side 2 are 28 mmHg and 52 mmHg, respectively. Assume ahydraulic conductance of 4.0 x 10-6 cm/Pa-s and total area of 2.0 m2for the membrane. Which direction will the fluid flow an

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A square bottomed tank measures 25*25*160cm and is positioned with the bottom of the tank 1m above sea level and at 20degreesC. The tank is 90% filled with water and 10% air. A water inlet enters the centre of the tank of 10mm diameter, and no other inlet or outlet is open within the tank. A pump drives water at a starting rate of 450ml/min at 0 Pa lowering to 350ml/min as the pressure increases to 800 kPa. The pump and tank are connected by a 10mm diameter pipe with k=0.15 for all fittings and tubing. It should be assumed this is the maximum flow and pressure provided by the pump. The pump will stop instantaneously once the pressure reaches 800kPa. The relationship between flow and pressure from the pump should be assumed linear. What will be the volume of compressed air inside the tank and how long will it take to fill?
Question 2) The centrifugal pump in the figure is in his preference Passing water at 25°C from the tank through the 1.22 m exchange store pumping. Inner diameter of the suction channel is 101.6 mm, in total it is 0.0306 and its length is 3.2 m. It the local coefficients of the user in the pipe are 7.4. If the pump works at a flow rate of 109 m3/h ENPY=1.52 is m. Does the pump work without cavitation at this flow? Show the calculation. For water, p=997 kg/m3 and Pb=3.169 kPa. Piping system at the entrance (Suction pipe) pump 22 Patm=101.3 kPa and 0.2=1.05. van
Rush, help me solve this one
The longest pipe run for a hot water system is 100 m. If the pressure rise through the pump is 35 kPa, then the pressure drop per one meter in system is إختر أحد الخيارات: Pa/m 233.3 .a O Pa/m 400 .bO Pa/m 250 .c O Pa/m 375 .d O
A pumping system has the following characteristics, f=0.015 length of thepipe = (2500 ft) pipe diameter 6 in, losses less than 0.5, the pipeis cast iron, and the system curve is:Hp= 34+ 5.47Q2Knowing that the system curve and the pump curve intersect at 12 cfsa. Determine Operation headb. Determine dischargec. Plot the system curve
In our house water pipe line with diameter of 2cm is connected to shower head that has 35 holes. The speed of the water in the pipe line is 1.1m/sec. i) What is the volume flow rate in the pipe line? ii) At what speed does the water leave one of the holes with diameter 0.0014m in the shower head?
ANSWER ASAP PLEASE
A vane pump with a volumetric efficiency of 82% and amechanical efficiency of 80%. Calculate the mechanical power required (Hp) to drive it if the working pressure is 1800 psi and a flow rate of 20 gpm? Answer:32Hp
An existing pump is used to pump water with the following data at BEP: D = 2.15 in, N = 1784 rpm, ρ = 998 kg/m3, Q = 18 gpm, H = 4.2 ft. A larger pump is to be designed based from the existing one to be used for pumping slurry (ρ = 1220 kg/m3) such that its best efficiency point occurs as close as possible to a volume flow rate of 48 gpm and at a net head of 15 ft. Calculate the new pump diameter in inches. Round off your final answer to 3 decimal places.
Containers A and B containing real fluid are combined like. While the difference of water levels of the reservoirs is h = ab (m); i-) Find the flow rate of the water passing from chamber A to chamber B. ii-) Draw the Energy and Piezometer lines of the system. g = 9.81 m / s
1. Identify and explain the different types of mechanical and electrical pressureelements. 2. Discuss the types of compressors. 3. Explain the principle of hydraulics. 4. Discuss the components of hydraulic system
An aqueduct is required to supply water to the community.Data: Families = 12 Average members per family = 3 people Breakfast, lunch and dinner = 15 total liters / family Showers = 10lt / person, one daily shower Kitchen wash = 13lts / day Total distance of the pipeline to the storage tank = 1200 meters Total height H from the pump point to delivery to the tank = 70 meters Determine: Estimation of the total volume of the recommended tank, an autonomy of at leas 2 days of storage. It is required to propose a pump that allows at least filling the tank between 5 to 12 hours operation, it must include details of the pump, as well as its curve Image: schematic detail of the proposed system