Three pipes A, B and C are interconnected as shown in Figure 1. The pipe dimensions are as follows : 1)Find the the rate at which water will flow in each pipe, ignoring the shock losses at P 2)Find the pressure at P

Three pipes A, B and C are interconnected as shown in Figure 1. The pipe dimensions are as follows : 1)Find the the rate at which water will flow in each pipe, ignoring the shock losses at P 2)Find the pressure at P

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1. The figure below shows a hot water tank, with a pumping arrangement to continuously circulate water in a loop. Plastic pipes used, with six bends and two gate valves, as shown. Given that the water is flowing at an average velocity of 2.5 m/s, calculate the required power input for the pump. Given: The density and viscosity of water at 60°C are p = 983.3 kg/m', u = 0.467x103 kg/m-s. Plastic pipes are smooth, and thus their roughness is very close to zero, ɛ = 0. The loss coefficient is K1 = 0.9 for a threaded 90° smooth bend and K1 = 0.2 for a fully open gate valve. Assume 70% pump efficiency. 1.2 cm Hot Water tank 40 m
2. A main pipe GH branched into three pipes; HI, HJ and HK. A liquid flow with a flow rate of 25 liters/minute via piping HI. If the flowrate in the pipe GH is three times greater than the rate of flow in the pipe HJ and HI flow rate is 1.5 times less than the rate of flow in the pipe HJ. a. Calculate the flow rate in the main pipe GH. b. Get diameter pipes HK if the mean velocity in the pipe HK is 2.3 m/s
water flows through 30 mm internal diameter pipe at atmospheric pressure. pitot tube measures the velocity of water at the center of pipe as shown in the fig. the pressure difference between the impact tube and the static tube is 20cm of carbon tetrachloride (density: 1600 kg/m³). calculate the volumetric flow rate through the pipe in cubic meter per hour. velocity of water is cp.
Given: diameter of pipe in point 1 = 3.9indiameter of pipe in point 2 = 2.5inspecific gravity of the liquid = 0.79h(ft) = 0.60ftpressure at point 1 = 14.6 psiapressure at point 2 = 49 psiapump and motor efficiency = 66%diameter of pipe in point 4 = 4.5indiameter of pipe in point 5 = 2.3 inZ3 = 35ft With the schematic diagram of a pump, tanks, and piping determine the following:1) The velocity of the liquid at point 2 (ft/s)2) Pump work used by the liquid (Wpump U) (hp)3) Electric motor power in out (kW)4) In figure 3, the shaded (pink) in the U tube is mercury; determine y. specific gravity of mercury 13.75) Mass flow rate
Q2' A pipe with a radius of 15 mm is attached to a garden hose with a nozzle. If the velocity of flow in the pipe is 4 m/s, what is the velocity of the flow at the nozle when it is adjusted to have a diameter of 16 millimeters, and what is the flow rate?
A pitot-static probe is used to determine the flow velocity by measuring the differential pressure as shown in Figure 7. The pressure difference sensor used in the system is electronic types and the output of the device is measured in voltage. The output of the pressure device is 3.5 V and the linear relationship between the device and the pressure difference is 10 kPa/v. i. Derive pitot formula to obtain flow velocity from Bernoulli equation, ii. Calculate the pressure difference inside the system, iii. Determine the velocity inside the system if the the fluid is water, and iv. Explain the cause that / ontirbute to inaccurary in the velocity reading. Fluid Flow, V Stagnation Static pressure pressure Pi-P2 Figure 7: Pitot static probe
Water falls into a vane and it ejected through two pipes. The inlet has a cross-sectional areas of Ao and the flowrate is Qo. The exits have flow rates of Q₁ and Q2, and cross- sectional areas of A₁ and A₂, respectively, as shown in Figure Q2. Pipes 1 and 2 are deflected at angles of 0₁ and 0₂ with respect to the horizontal, as shown. Assume that the fluid at each inlet and outlet is at atmospheric pressure. The flowrates do not change with time. a) Find an expression for Q2 b) If the horizontal force on the vane is zero, find an expression for Q₂ in terms of the other flow rates, areas and angles c) Find an expression for the vertical force on the vane in terms of the flow rates, areas and angles Q₁ 0₁ A₁ le Ao 10₂ A₂ 22 Figure Q2: Fluid entering a vanes and exiting in 2 directions.
Water is contained in both sides of the cylinder system shown below and the valve is closed. If the pressure on the right hand side of the valve is 119.6 kPa, what is the height in tank B, i.e. what is hp 1? Assume that the atmospheric pressure is 100 kPa, the acceleration due to gravity is 9.807 m/s² and the density of water is 1000 kg/m³. A Po B ha,1=1.5 m Water Water hg,1 1.0 m 0.5 m Pval,left Pyal,right A) 1.0 m B) 1.5 m C) 2.0 m D) 2.5 m
The diameter of a pipe at the larger end is 0.6 cm and at the smaller side is 0.3 cm the larger and smaller ends are located 8 meters and 4 meters, respectively, from a datum line. If at the larger end the velocity is 1.2 meters pee second and the pressure is 5300 kN/m^2, compute the pressure at the smaller end
As shown in the figure, the water is directed downward in the installation with a 25 ° angle narrowing elbow in a piping system with a volumetric flow of 0.025 m3 / s. Effective pressure at 1 point is measured as 2 bar. Where the flow is frictionless and gravitational effects are neglected, a) Find the effective pressure at point 2. b) Calculate the x and y components of the force needed to hold the elbow in place and the resultant force. (psu =1000 kg/m3, g = 9.81 m/s2).