A vertical, cylindrical tank, 6 ft in diameter and 12 ft high, is held together by means of two steel hoops,one at the top and one at the bottom. Molasses (SGmalasses = 1.50) stands to a depth of 9 ft in the tank.The cross-sectional area of each hoop is 0.5 in?. The tank is open at the top. Let T1 and T2 be the tensileforces in the top and bottom hoops, respectively, and oi and o2, the stresses in the top and bottomhoops, respectively. Determine the following:ParameterUnit(a) FTOTAL(b) T1IbIb(c) T2Ib(d) 01psi(e) 02psi

Given: D= 6 ft H=12 ft h=9 ft sg=1.5 density=1500 kg/m^3=93.64 lb/ft^3 A=0.5 in^2 TO determine: The…

Answered: Parameter Unit (a) FTOTAL (b) T1 (c) T2…

Engineering

Mechanical Engineering

Parameter Unit (a) FTOTAL (b) T1 (c) T2 (d) 01 (e) o2 Ib Ib Ib psi psi elele

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

• Temperature plot scoped to steam pipe (cast iron) in C° units. Fill in the below table. Compute the temperature drop up to THREE decimal places (see hint given below). Temp drop in Insulator Temp drop in Pipe ANSYS Results • Include the above table in your submission.
Q: Experiment of venturi meter. Please give a brief description for Bernoulli’s equation. What typeof parameters can be derived from an experiment?
Conduction Heat Transfer X material (a) material (b) . both (a) and (b) have the same thermal conductivity the temperature distribution is independent of thermal conductivity it's not that simple 9. Fin efficiency is defined as: • tanh (mL) (hP/k Ac)1/2 (heat transfer with fin) / (heat transfer without fin) (actual heat transfer through fin) / (heat transfer assuming all fin is at T = Tb) (Tx=L-Tf)/(Tb-Tf) 10. For an infinite fin, the temperature distribution is given by: (T-Tf)/(Tb-Tf)= e-mx. The heat flow through the fin is therefore given by: k (Tb-Tf)/L ● zero, because the fin is infinite ● infinite because the fin is infinite ● (Tb-Tf) (hP/k Ac)1/2 ● (Tb – Tf) (h P / k Ac)1/2 tanh (mL) 11. The Biot number, Bi, is defined as: • Bi=hk/L • Bi=hL/k • Bi= k/LH • Bi=qL/k • Bi=p UL/k 12. For a plate of length L, thickness, t, and width, W, subjected to convection on the two faces of area L x W. What is the correct length scale for use in the Biot number? . L ● W ● t • t/2 • L/2 13. If Bi…
Need help with the calculations i keep getting lost in the conversions
Q8): To find how much heat is required to bring a kettle of water to its boiling point, you are asked to calculate the specific heat of water at 61°C. The specific heat of water is given as a function of time in Table below. Temperature, T Specific heat, C₂ (°C) J kg-°C 22 42 52 82 100 4181 4179 4186 4199 4217 Determine the value of the specific heat at 7=61°C using the direct T method of interpolation and a third order polynomial. Find the absolute relative approximate error for the third order polynomial approximation (Lagrange Method).
I need the correct response and the formula to solve this problem please,I need h and Ay, several couples of answers are given.Only one is correct. Thank you
4G I. uols -a moodle1.du.edu.om IVIGI Ncu vut UI .00 P Flag question Consider the system is the following figure. K = 4 N/m x,(1) K2 = 5 N/m x(1) fy. = 3 N-s/m M =1 kg|Jv2=3 N-s/m M, = 2 kg f= 2 N-s/m The differential equations of the system is [3*, + 5x, +9x, - 3x, - 5x, - f() | 2i, +5i, +5x,-34, - Sx, =0 *, + 6x, +9x, - 3i, - Sx, = 0 |25, + Si, + Sx, - 3i, -5x, = /(1) |+6i, +9x, - 3x, -5x, = 0 i, + 6i, +9x, - 3x, - 5x, =0 b. d. li, + 5i, +5x, - 3x, - x, = f(0) LE, + 5i, + 5x, - 34, -4x, = f() Select one: O a. d b. a O c. C O d. b Previous page Finish attempt ... 1 Test 1 Jump to... Grades Assignment 1 and Test 1
Need help with engineering problem. Match the RTT term with its explanation: A: ddt(∫CVβρdᏉ) B: ∫CSβρVcosθdAout C: ∫CSβρVcosθdAin A. B. C. Match one of the following answers below to each letter. A change within the control volume Outflow of B from the ontrol volume Inflow of B to the control volume
For a venturi meter given below, the volumetric flow rate is defined in terms of the geometrical parameters, the density of working fluid (p), and density of the manometer liquid (pm) as 4. Q = f(D, D2, A2, g, h, Pmv Pr) %3D Write down the balance equations and show your work to end up with an expression for the volumetric flow rate in terms of the variables defined above.
Find V, u and S in steam table using ideal gas properties for air. and provide steam table where u get the value thanks
Vibration
I need help with parts d, e, and f please.