P-30 KN Q1/ Two solid cylindrical rods are joined at B and loaded as shown. Rod AB is made of steel (E-200 GPa) and rod BC of brass (E =105 GPa). Determine (a) the -30 mm total deformation of the composite rod ABC, (b) the deflection of point B. 40 kN 00 m 50 mm

Q: Observe the figure that shows the assembly of the ACD arm, suspended by a bearing in C coupled to a…

A:

Q: The hanger assembly shown is used to suspend equipment from the ceiling. The length of rod AB is LAB…

A:

Q: The rigid arm AB is attached to the end of the solid circular steel rod BC. The rod is supported by…

A:

Q: plz see screeshot

A: if you have any doubt please comment

Q: Required information Members AB and BE of the truss shown consist of 25-mm-diameter steel rods (E=…

A: Diameter (d)=25 mmA=π4×252=490.873 mm2E=200 GPaP=69 kNNow, let us assume the angle between truss DE…

Q: The assembly consists of three titanium (Ti-6A1-4V) rods and a rigid bar AC. Agr=2 in² 1 ft F-2A- P…

A: GivenApplied force Length of rod AB and CD cross-section area of rod AB and CD is Length of rod EF…

Q: n the steel structure shown in the figure, a 6 mm diameter in is used at C and 10 mm diameter pins…

A:

Q: 3. A shaft composed of segments AC, CD and DB is fastened to rigid walls and loaded as shown. For…

A: Solution:(a) Free Body Diagram (FBD) of the Composite ShaftFirst, let's understand the torques at…

Q: A rectangular column is made of a grade of sawn wood that has an adjusted allowable stress for…

A: Write the given data. σC=8.3 MPaE=11.1 GPaP=105 kNe=0.025 mb=0.180 md=0.240 m

Q: A rectangular column is made of a grade of sawn wood that has an adjusted allowable stress for…

A: Write the given data. σC=8.3 MPaE=11.1 GPaP=88 kNe=0.025 mb=0.180 md=0.240 m

Q: 1) For the steel rod shown with elastic modulus of E = 29 Mpsi, determine: a) The average normal…

A:

Q: 3. A circular flat plate of 120 mm diameter and 6-35 mm thickness is clamped at the edges and…

A: Given data Diameter of flat plate = 120 mm = 0.12 m Thickness = 6.35 mm = 0.00635 m Uniform lateral…

Q: 2. (20%) A rod of diameter, 22 mm is fixed into a wall as shown and subjected to a uniform axial…

A: The forces are The distributed load isThe length are The diameter is

Q: Required information Both portions of the rod ABC are made of an aluminum for which E= 70 GPa.…

A: Calculated deformation of point B.

Q: The wing spar ABD of a light plane is made from 2014-T6 aluminum and has a cross- sectional area of…

A: The cross-sectional area is A=800 mm2 The moment of inertia about the neutral axis is I=1.07*10-6 m4…

Q: Two solid cylindrical rods support a load of P = 25 kN as shown. Determine the axial load in rod…

A:

Q: A 10 m length shaft is used to transmit 50 kw power at 450 rpm. If the shaft stress is limited to 40…

A: Given    Length, L = 10 m     Power, P = 50 kW    Speed, N = 450 rpm          Stress = 40 MPa Find…

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ =…

A:

Q: ..

A: Deflection will be calculated due to vertical loading only ∑Fy= 0 → RB+ RG         = 25+5 ×…

Q: 1) A steel bar of 15 mm in diameter was bent as shown. Using the method of work and energy,…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.