1) A steel bar of 15 mm in diameter was bent as shown. Using the method of work and energy, determine the defiexion at the C end, due to the force of 200 N

Q: Required informetion Consider the beam and loading shown where P= 42 kips. 3 kipvt From the figures…

A:

Q: 43. A semi-circular arch with a radius of 1 m is subjected to a concentrated load of 2.8 kN at point…

A:

Q: A 60 mm- В 90 mm- 100 mm C 4 kN 80 mm D 140 mm

A:

Q: 4. Draw the FBD of member DABC 12 in. 12 in. A 150 lb B ----- -3 ft -5 in D 5. Draw the FBD of…

A:

Q: Member BC shown is subjected to a vertical force of 45 kN. Determine the position S of this force so…

A:

Q: (5) When the bar subjected to torque, the maximum shear stress occur at.. O A. External surface of…

A: When a bar is subjected to the torque, the shear stress will be produced in the bar.

Q: 1. A circular piece of wood, 90mm in diameter, is used as a compression block. Determine the axial…

A:

Q: Determine the distance x to the that the load of 500kN must be, in such so that the resultant of the…

A: Free body diagram is drawn in above image.

Q: Determinethe magnitude (b) of the horizontal component of force at point C if P = 126.6 lb, x= 13.2…

A:

Q: Determine the loads acting on pins A and D of the frame shown. On the other hand, if the pin at B…

A: Given data  Given figure  The pin at B can withstand a maximum shear force (F)= 800 lb

Q: Determine the shear force 6.21 ft to the right of point A for the beam shown belowif T = 1123 lb ft,…

A:

Q: 7. Straight rods of 0.4ft diameter and 100ft length are stored by coiling the rods inside a drum of…

A:

Q: Knowing that for the extruded beam shown the allowable stress is 120 MPa in tension and 153 MPa in…

A:

Q: Q2) The aluminum rod BC (G-26 GPa) is bonded to the brass rod AB (G-39 GPa). Knowing that Birass…

A: For solution refer below images.

Q: Determine the diameter (in mm) of the largest circular hole that can be punched into a sheet of…

A:

Q: A cable AB of span L and a simple beam A'B' of the same span are subjected to identical vertical…

A: The free-body diagram of the cable is as follows, Consider moment about B (FBD of cable),

Q: 2. Bending moment, M; is applied about z axis. If the normal stress due to bending moment at point A…

A: GIVEN :-(σx)A=43MPa DIAGRAM :-   SOLUTION:- from the figure,y1=22.5 mmy2=22.5 mmy3=47.5 mmand,…

Q: Solve magnitude P using method of sections if DG is -15kN

A: Calculated magnitude P using method of sections if DG is -15 kN .

Q: Determine the internal forces at point J when a= = 0.

A: Given,

Q: The beam is made up of four boards, and is subjected to a moment of M-200 kip in, calculate the…

A: To find :  The resultant force on the top board C. Given :  The moment is  M=200 kip. Formula Used :…

Q: Do not round intermediate answers. Give your final answer(s) to three decimal places. Check your…

A: σall=24ksiE=29×106psi   To-Find:- a)The Largest Couple M2) The Corresponding Radius of curvature

Q: Take that w1 120 N/m and w2 = 180 N/m. W1 B, -6 m - 5 m Ľ. W2 Part A Replace the distributed loading…

A:

Q: A sketch of a bolt cutting tool is shown. Material of all parts is steel. Dimensions are in inches.…

A:

Q: Determine the resultant internal loadings acting on the cross-sections at points D and E of the…

A: The free body of the beam is as follows: Calculate the moment about point A as follows:…

Q: Determine the bending maximum stress in the steel strip loaded and supported by pins as shown. 3" 5"…

A:

Q: 3 m 500 N/m 1.5 m A 2 m F D B 2 m 900 N Show Transcribed Text E ΤΟΙ·ΙΟΣ 750 N 3 m determine a- the…

A:

Q: Q2:- Find the maximum shearing stress due to the applied forces in the plane AB of the 10mm diameter…

A:

Q: 1. The axle of the car is subjected to forces and moment shown, where the diameter of the axle is…

A: Let us consider the given data,The diameter of the solid axle is .The torque To Find:(i) The…

Q: Which of the following set of internal loads develop in section a-a with the application of the…

A: To find set of internal loads develop in section a-a with the application of the downward force

Q: Determine the internal resisting forces and moment trans- mitted by section aa in 3 kN 120 mm D 100…

A: Consider the free body diagram shown below for the member ABC.

Q: knowing that the allowable stress in the bar shown is 10 ksi, find the allowable bending moment "M"…

A:

Q: (5) The bent uniform slender bar of mass 2m and length 2L is suspended by the two strings as shown.…

A:

Q: 3 Knowing that for the extruded beam shown the allowable stress is 120 MPa in tension and 149 MPa in…

A: Please see the attached image for the answer.Explanation:

Q: The beam shown is made of a nylon for which the allowable stress is 24 MPa in tension and 31 MPa in…

A:

Q: B 60 mm -40mm- D The homogeneous wire ABCD is bent as shown and is attached to a hinge at C.…

A: Given : Distance AC = 60mmDistance between CD = 100mm

Q: Determine the internal forces at points F and G. F is located 0.7 m to the right of support A G is…

A:

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.