For a given gripping force P, determine the normal force Q exerted on the small round stock by each jaw of the compound pliers. B Answer: Q = i C 3.9"1" 2.6"- D 5.9" P

Q: could you pls provide part D and E

A:

Q: 12-34. Design a cylindrical tank for compressed natural gas at a pres- sure of 4.20 MPa. The minimum…

A: The pressure is The minimum inside diameter is The factor safety is The cylinder material is…

Q: advantages and 5 disadvantages of using trash pumpp

A:

Q: what would be the order of operations to make this part in the least amount of time and how would…

A: The order of operations to make this part in the least amount of time and how would you hold the…

Q: Arm ABCD is pinned at B and undergoes reciprocating motion such that 0 = (0.3 sin 4t) rad, where t…

A: Length BD   Length BA Find the largest speed of A and the acceleration of point D

Q: 2 cosh(lnx)

A: to find: 2cosh(lnx)

Q: Differentiate between single acting and double acting cylinders.

A: Differentiate between Single Acting & Double Acting Cylinder :

Q: Determine the distance and resultant of the five parallel forces acting on the rocker arm of the…

A:

Q: the parts of a micture can be         using the physical properties of the compund

A: Compounds are substances made up of two or more elements whereas mixtures are made up of elements or…

Q: A faxe 5kN opblied 1SKN on Hod a°cirular sechonal Detrimine dtress snas area SmmL. of

A: Given data :Load (P)=5 KNArea (A)=5 mm2

Q: Instruction: Explain briefly the difference between Annealing and NOrmalizing

A:

Q: SKN |SkN 4kV/m 15m 1.5

A:

Q: Describe Scavenging

A: IC engine completes one power stroke in four strokes. Intake of A/F mixture Compression Power…

Q: DESCRIBE THE PROCESSES AND CYCLES?

A: Consider the PV diagram shown below for a process and cycle.

Q: also why is Q/T0 being subtracted in sgen1 while other 2 its being added

A:

Q: Limit Gauge loose fit, slide fit, easy sliding fit, running fit Go & No Go Ends O the difference…

A: As per our guidelines we are supposed to answer only one question if multiple questions are asked.…

Q: Where did the 107.11 came from

A: Given   Weight, W1 = 500 N                 W2 = 1000 N Find   The angle 107.11o

Q: Differentite between enclosure hoods, canopy hoods, and capturing hoods.

A: A capturing hood is a device that channels the outflow of air from an air conditioning system. It…

Q: If a wrench is unable to loosen a wheel nut, what are two ways that you could increase the torque…

A: There are two ways to increase the Torque if a unable to loose the wheel nut

Q: What is planar motion?

A: Planar motion is the kind of motion where a body moves in a plane and has two degrees of freedom,…

Q: Define the following phrase; i. External forces ii. 111. iv. V. Forces generated by motion Forces…

A:

Q: Name 3 types of fits?

A: The different types of fits are : 1) Clearance fit 2) Interference fit 3) Transition fit

Q: Copra enters a dryer containing 60% water and 40% solids and leaves with 5% water and 95% solids.…

A:

Q: What are the methods to improve fatique life?

A: Fatigue life in weld joint is improved by following methods: 1.Reducing the stress concentration on…

Q: 6 m

A:

Q: What is the flow rate to a cylinder with a 3-in bore and 22-in stroke that fully extends in 8…

A:

Q: The task is to utilise ANSYS Workbench in the design and simulation of a linear, open-sidedcovered…

A: Step 1:Step 2:Step 3: Step 4:

Q: metaicfhread: Pitch- 3mm thocadaryle=65 using 3-wire meltad Best size wisre diametoe ?

A:

Q: what are the parts of a plumb bob

A: A plumb bob is an Instrument ,Which is used in construction and other fields to determine vertical…

Q: 7. What is the part’s over all depth?_______________________ 9. Which line does in the top view…

A: Solution     7. The part’s overall depth 1.50

Q: Name at least two fluids you can see on your household and provide photos for each.

A: Fluid- when any gas , liquid or any material which has ability to flow under application of any…

Q: Qi) Answer only Seren of the following multiple choice: 1- Green sand mold mean mixture of: a- Clay…

A: 1.Green Mould sand is a mixture of sand ,clay and water. Answer: Option c 2.Cores are made of high…

Q: The suitable manufacturing process for cast Iron is a. Injection Molding

A: Cast iron is obtained by reducing iron ore in a blast furnace. The liquid iron is casted followed by…

Q: 1. cubic yards equals 297 cu ft.

A: Note: Since you have asked multiple question, we will solve the first question for you. If you want…

Q: Q3:- One of the companies wanted to drill an oil well in one of the fields in depth (6000 ft and…

A: A moment is a movement of the body when a body is rotating on an axis. The moment is also known as…

Q: 18. Surface roughness comparators are used witry manufactured surface finish of a part or assembly…

A: The measurement of small-scale differences in the height of a physical surface is known as…

Q: 3) Glazing bars are made up of a. PVC b. High speed steel c. Low Carbon steel d. Aluminium

A: option  (a) is correct( PVC)

Q: ead intrustions on example and help anwser it please and th

A: Jsolid Cylinder =πd432 DAC = 0.9 JAC =π 0.9432=0.064412467

Q: where did you guys get the area from?

A:

Q: During the sand casting process, various types of patterns are used. Which of the following is not a…

A: Option (c) sprue pattern is correct option

Q: The first element in a feature control frame in Solidworks denotes what?

A: The products may vary slightly in terms of dimensions as compared to the initial designs because of…

Q: Explain the following with appropriate examples (at least 2 examples) 1. Grubler's criterion. 2.…

A: The Grubler's criterion gives the number of degrees of freedom of a mechanism involving links and…

Q: What is the reason qhy HRSG HP, IP & LP drum separate from wet of ground using a wooden support…

A: 1. HRSG HP Drum (High-Pressure Drum) Separation from Wet Ground using Wooden Support :   To prevent…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.