b) Fig. 3 shows a graph that has variable drive torque and constant load torque. The load ( torque is 500Nm with average speed of 30rpm. A complete cycle for the system is 3x radian. Determine thickness of the flywheel if you want to reduce the coefficient speed of fluctiation from 0.15 to 0.1. Assume the diameter for the flywheel is 50cm and material used is steel (p=8050kg/m³) Le.. Torque (N-m) 12 cm 750 220 T 2n } 813 8 3n 3 E 8(rad)

b) Fig. 3 shows a graph that has variable drive torque and constant load torque. The load ( torque is 500Nm with average speed of 30rpm. A complete cycle for the system is 3x radian. Determine thickness of the flywheel if you want to reduce the coefficient speed of fluctiation from 0.15 to 0.1. Assume the diameter for the flywheel is 50cm and material used is steel (p=8050kg/m³) Le.. Torque (N-m) 12 cm 750 220 T 2n } 813 8 3n 3 E 8(rad)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please answer immediately thank you
. A pulley used to transmit power by means of ropes has a diameter of 3.5 m and has grooves of 45° angle. The angle of contact is 160° and coefficient of friction between the ropes and groove sides is 0.3. The maximum possible tension in the rope is 1000 N ad the mass of rope is 1.5 kg per metre length. What is the speed of the pulley in rpm and the power transmitted if the condition of maximum power prevail? 10
The following observations have hecn ndo from the test of a four- cylinder, two-stroke gasoline engine. Diameter speed = 1600 rpm; Area of the positive loop of the indicatortagram 5.75 sq cm: Area of the negative loop of the indicator diagram sq cm: Length of the indicator diagmnge 3.5 bar/cm; Find the indicated power {he engine. = 10 cm; str d 15 cm; 25 55 mm: Spring cons = ||
Do not use shift solve show complete solution
give the a) A turbine connected to an electric generator through a gearbox can be modelled as illustrated in Figure 1 = 951 kgm² J2 = 950 kgm² equivalent inertias of the rotary system. The shafts provide a stiffness of k1 = 9.9x10¹Nm/Rad k2 = 4.9x106Nm/Rad spectively. The letters in the parameters represent digits of student numbers: A is the third digit, B is the fifth digit, D is the sixth digit, and F is the seventh digit. i) Draw free-body diagrams ii) Write the equations and put them in matrix form iii) Calculate the dynamic stiffness values iv) Find the natural frequencies and draw mode shapes of the system v) Discuss the effect of coupling stiffness k₁₂ on the natural frequencies k₁₁ 01 k12 O Figure Q2.
Use graph above Two blocks are positioned on surfaces, each inclined at the same angle of 57.6 degrees with respect to the horizontal. The blocks are connected by a rope which rests on a frictionless pulley at the top of the inclines as shown, so the blocks can slide together. The mass of the black block is 6.42 kg, and the coefficient of kinetic friction for both blocks and inclines is 0.560. Assume static friction has been overcome and that everything can slide. What is must be the mass of the white block if both blocks are to slide to the RIGHT at an acceleration of 1.5 m/s^2? 4.55 kg 2.03 kg 1.94 kg 2.50 kg
A1 A grinding wheel used in machine shop needs to be analyzed in terms of its suitability for a specific grinding task. Find 1. Accelerating torque produced by the grinding wheel II. Increase in angular momentum of the grinding wheel II. Increase in Kinetic energy of the grinding wheel. Assume the following data Suitable mass of the grinding wheel. Suitable radius of grinding wheel. Select any two Speeds between range 1000 – 3000 rpm. Consider 20 seconds time gap between two speeds selected. 1. 2. 3. 4. Justify your data assumptions.
Torsian in a Bolid wY Awollow tube The figure above shows a rig which is used to find the angle of twist for a shaft. A torque is applied to the shaft by applying a force to the torque arm, as shov on the right hand side of the figure above. Given Load applied to end of torque arm = 90 N Length of torque moment arm = 150 mm Length of shaft(L) = 300 mm Young's modulus of steel = 205 kN/mm22 Modulus of rigidity 84 kN/mm22 Solid shaft diameter = 15 mm
Problem 6Given: A 1:40 scale model of a submarine propeller is tested in a tow tank at 1500 rpm and exhibits a power of 1.4 ft-lb/s. Required: Using Froude’s scaling law, determine the rpm and power output of the prototype propeller under dynamically similar conditions. (Hint: 1500 rpm is a velocity term and Power = Force*Velocity)
Please provide clear solution and FBD and please answer within 30 minutes, Thank you!
b) For the torsion bar shown below: 3) Derive the equations as functions of the independent variable and the input variables for Mx, Øx9, Ex8, and 0 4) Plot the graphs of the above four variables in the order listed above as functions of the independent variable A=constant Right end is fixed (0(x=L)=0) G=constant T Left end is fixed (0(x=0)=0) L/2 L/2
you are offered a choice of an incremental shaft encoder or an absolute shaft encoder for the measurement of an angular displacement. what is the principal difference between the results that can be obtained by these methods ?