Output at 0.8 p.1. Example 33.3. A 3-phase, 6,600/415-V, 2,000-kVA transformer has a per unit resistance of 0.02 and a per unit leakage reactance of 0.1. Calculate the Cu loss and regulation at full-load 0.8 p.f. Univ. 1987) lag. (Electrical Machines-I, Bombay

Output at 0.8 p.1. Example 33.3. A 3-phase, 6,600/415-V, 2,000-kVA transformer has a per unit resistance of 0.02 and a per unit leakage reactance of 0.1. Calculate the Cu loss and regulation at full-load 0.8 p.f. Univ. 1987) lag. (Electrical Machines-I, Bombay

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Consider the three single-phase two-winding transformers shown in Figure. 3. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in A, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a', b', and c' such that VAN is 90° out of phase with V₂'b' for positive sequence. DI H₂ Figure. 3: Three-Winding Transformer
A 11000/230 V, 150-kVA, 1-phase, 50-Hz transformer has core loss of 1.4 kWand full load copper loss of 1.6 kW. Determine (a) the kVA load for max. efficiency and(b) the value of max. efficiency at unity power factor
please answer in short....please....i will like.
YVTA io YVIA Q1) Fill in the blanks by inserting appropriate words/numbers 1- The high value of efficiency in voltage distribution over suspension insulator string is because of ... .... a) grading the insulators. b) using short cross-arms. c) using a guard ring. d) using longer cross-arms. 2- The per unit value of the transformer in the figure below is ... . assume the Spase is 50 MVA and Vese 20 kV in generator side. 50 0.3 P.u 0.2 p.u 20 MVA 20 MVA 25 KV 25 /33KV 3- During the critical disruptive voltage .. a) the conductors are surrounded by a faint violet glow. b) appearing of high hissing noise c) high power losses may happened d) none of the all above 4- If each of the power system component is represented by its equivalent circuit in a diagram, then this diagram is called .......... a) single line diagram b) impedance diagram c) reactance diagram d) power flow diagram. 8.
1. Find the all-day efficiency of a transformer having maximum efficiency of 96% at 30-kVA load at UPF. If during the day the transformer is loaded as follows: 12 hours.... 6 hours... .5 kW at 0.6 p.f. lagging ..24 kW at 0.8 p.f. lagging 6 hours..... ..at no-load.
III. Express the notations below in rectangular and polar form ej0.92 7. jn 8. е6 j4n 9. е з
8- A transformer, when tested on full-load, is found to have Cu loss 1.8% and reactance drop 3.8%. Calculate its full-load regulation (i) at unity p.f. (ii) 0.8 p.f. lagging (iii) 0.8 p.f. leading.
Construct the circuit in Figure 1 in the Circuit JS simulator. Note that the voltage source is given in RMS. Within Circuit JS while defining the max voltage of the voltage source include “rms” after the number to tell Circuit JS that this is a rms value. Also note that there are additional parameters when instantiating a transformer in Circuit JS. Leave these at the default values. Additionally, transformers may have problems simulating in Circuit JS. Answer the following: 1. From the simulation results, determine the power dissipated in R2 and compare to the expected value from the previous section.2. Change the transformer ratio (“Ratio” as a fraction when you “Edit…” the transformer component) to the value calculated in the previous section to provide maximum power transfer in R2. Note: In Circuit JS, Transformer Ratio = Primary/Secondary.3. Rerun the simulation, calculate the power dissipated in R2 and compare to the expected value from the previous section.4. Change the…
The label values of the single-phase transformer whose electrical equivalent circuit is given below are 20 kVA, 15400V / 240V, 50 Hz. This transformer Calculate what is required below. a. What is the value of the active power measured in the short circuit test? b. What is the value of the active power measured in the idle test? c. Voltage regulation was found to be 0.1% at 0.8 back power factor. Accordingly, using any method you want Find out how many kVA the transformer draws from the network (primary apparent power).
Q5:Choose the correct answer from the given alternatives (answer five only) 1.In an ideal transformer, (a) windings have no resistance (b) core has infinite permeability (d) all of the above. (c) core has no losses 2. The primary and secondary induced e.m.fs. El and E2 in a two-winding transformer are always: (a) equal in magnitude (b) in-phase with each other (c) antiphase with each other (d) determined by load on transformer secondary. 3. In relation to a transformer, the ratio 20 : 1 indicates that (a) there are 20 turns on primary one turn on secondary (b) secondary voltage is 1/20th of primary voltage (c) primary current is 20 times greater than the secondary current. (d) for every 20 turns on primary, there is one turn on secondary. 4. A transformer has negative voltage regulation when its load power factor is: (a) zero (b) lagging. (d) unity (c) leading
Vr 3. For a 1.2 accuracy class potential transformer used at a lagging phase angle y of 10', the RCF value is A. 0.991. B. 0.988. C. 0.977. D. 0.999. primary connection scheme that must be used with
a) Express the general formula for a transformer’s energy efficiency when in on-loadoperation, and briefly explain the losses included in the expression.