Q-3: A balanced three phase source supplies 220 V, to a balance three phase load. If the line current Ia is measured to be 12A and is in phase with line-to-line voltage Vbc, then find the per phase load impedance if the load is: (a) Y- Connected (b) A-Connected. (Assume phase quantity as reference and assume -ve sequence)

Q-3: A balanced three phase source supplies 220 V, to a balance three phase load. If the line current Ia is measured to be 12A and is in phase with line-to-line voltage Vbc, then find the per phase load impedance if the load is: (a) Y- Connected (b) A-Connected. (Assume phase quantity as reference and assume -ve sequence)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q22) Consider a 3-phase, 33 kV transformers with N1:N2 = 900:150. Calculate the secondary line voltage on no load condition the windings are connected in the following configurations i) Star-Delta. ii) Delta-Delta.
An Alternator having three-phase, 3-wire ABC system supplying an effective line voltage of 120 V, has an athree-impedances of 50 / 45 ohms in Delta connection. Assume that Vbc is the reference vector. Determine a) linecurrent and line voltages with its degrees, b)Draw the current –voltage phasor diagram c) and the power generated inthe line quantities of the alternator.
In Figure 1, the 3-phase source has a line-to-line voltage of 440 volts. The details of the impedances are the following: Z₁ = 36-j15; Z₂ = 40 + /300; Z₂ = 45+j60 ; Z₂ = 75 + jo ; Z5 = 50+j50; Z6 = 20+ j48 2. Determine the following: (a) Line currents: labi, and I (c) Line currents: lar, Ibr, and ICT; (b) Line currents: Iaz, Ibz, and Iczi (d) PT, QT, ST, and pft for the system; (e) W, and W, readings for 2-wattmeter method at lines a and b. Balanced 3-Phase ab-bc-ca source C Figure 1 →laT -Ibr -KT 1 lal ²3 ↓ Ibi 1 Ici la2 lb2 le2ܝ 150 1²₂ OND
Problem 3.5: From a 3-phase, 480 V generator switchboard, a feeder takes 3-phase power to two equipment at the other end via cable and trans- former with the combined series impedance Z = 0.04 + j 0.09 N per phase. The voltage at receiving end point A rises and falls as a large 3-phase, 500 kVA load at point A varies over time. The small 1 kVA load, also connected at point A, remains online continuously, and must accommodate the voltage variations at point A with the 500 kVA load fully on or fully off. Determine the voltage range that the 1 kVA load will see, over which it must perform within its specifications.
Note: It is expected from student to develop impedance matrices of three phase power system. Develop impedance matrix (Z-bus) of power system network as shown in figure. [Values are given in per unit impedance.] j3 12 j3
18. A 415 V, 50 Hz, 3-phase supply of phase sequence RYB is connected to a delta connected load in which branch RY consists of R, = 100. branch YB conists of R₂ = 20 2 in series with X₂ = 60 Q and branch BR consists of a capacitor C= 30 uF. Take Vy as the reference and calculate the line currents. Draw the complete phasor diagrams. (Elect. Machines, A.M.I.E. Sec. B. 1989) 14.54, 1, 10.66 2172,92, 14.46 2-471 (1 = 7.78
2-What is the relationship between phase and line quantities in balanced star and delta connections in three phase circuit balanced ? Why?
Is it true??
1. Given the circuit below, the phase voltages are given by Van = 20040° Vrms. The source impedance is 5 + j7 per phase and the wire impedance is 8 +j10 per phase. Let the load impedance be Zy = 50 ohms. Find: Van Vin Ven a. II, and Ic b. c. VAN, VBN, and VCN, and VAB, VBC, and VCA Z₂ Z₂ Z₂ Zw Zw Zw B C le N
Solve A-E