1. Iron los...........varies approximately as V². 2. Cu loss..........it also varies as 2 but decreases with an increase in volta output is assumed. 3. Efficiency...........for distribution transformers, efficiency at fractional load crease in voltage while at full load or overload it increases with increase versa. 4. Regulation......... it varies as but decreases with increase in voltage if c is assumed. 5. Heating..........for constant kVA output, iron temperatures increase where decrease with increase in voltages and vice-versa.

1. Iron los...........varies approximately as V². 2. Cu loss..........it also varies as 2 but decreases with an increase in volta output is assumed. 3. Efficiency...........for distribution transformers, efficiency at fractional load crease in voltage while at full load or overload it increases with increase versa. 4. Regulation......... it varies as but decreases with increase in voltage if c is assumed. 5. Heating..........for constant kVA output, iron temperatures increase where decrease with increase in voltages and vice-versa.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Consider the three single-phase two-winding transformers shown in Figure. 3. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in A, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a', b', and c' such that VAN is 90° out of phase with V₂'b' for positive sequence. DI H₂ Figure. 3: Three-Winding Transformer
YVTA io YVIA Q1) Fill in the blanks by inserting appropriate words/numbers 1- The high value of efficiency in voltage distribution over suspension insulator string is because of ... .... a) grading the insulators. b) using short cross-arms. c) using a guard ring. d) using longer cross-arms. 2- The per unit value of the transformer in the figure below is ... . assume the Spase is 50 MVA and Vese 20 kV in generator side. 50 0.3 P.u 0.2 p.u 20 MVA 20 MVA 25 KV 25 /33KV 3- During the critical disruptive voltage .. a) the conductors are surrounded by a faint violet glow. b) appearing of high hissing noise c) high power losses may happened d) none of the all above 4- If each of the power system component is represented by its equivalent circuit in a diagram, then this diagram is called .......... a) single line diagram b) impedance diagram c) reactance diagram d) power flow diagram. 8.
1. Find the all-day efficiency of a transformer having maximum efficiency of 96% at 30-kVA load at UPF. If during the day the transformer is loaded as follows: 12 hours.... 6 hours... .5 kW at 0.6 p.f. lagging ..24 kW at 0.8 p.f. lagging 6 hours..... ..at no-load.
Construct the circuit in Figure 1 in the Circuit JS simulator. Note that the voltage source is given in RMS. Within Circuit JS while defining the max voltage of the voltage source include “rms” after the number to tell Circuit JS that this is a rms value. Also note that there are additional parameters when instantiating a transformer in Circuit JS. Leave these at the default values. Additionally, transformers may have problems simulating in Circuit JS. Answer the following: 1. From the simulation results, determine the power dissipated in R2 and compare to the expected value from the previous section.2. Change the transformer ratio (“Ratio” as a fraction when you “Edit…” the transformer component) to the value calculated in the previous section to provide maximum power transfer in R2. Note: In Circuit JS, Transformer Ratio = Primary/Secondary.3. Rerun the simulation, calculate the power dissipated in R2 and compare to the expected value from the previous section.4. Change the…
QUESTIONS: 1. A 10 kVA, single-phase, 2400-V:120-V, 60 Hz transformer has an equivalent impedance referred to LV side of 0.01 + j0.09 Q. This transformer has a core loss of 100 W at rated voltage. When rated current is applied to the 2400-V winding, the exciting current in that winding is found to be 0.2 A. a. Find the full-load regulation of this transformer at a power factor of 0.8 lagging. b. Find the efficiency of this transformer at full load, 0.8 power factor lagging. c. Ifstandard open-circuit and tests were performed on this transformer, what would be the measured values of these tests? 2. The following data were obtained on a 2.5 MVA, 50-Hz, 19.1-kV:3.81-kV single-phase transformer tested at 50 Hz: Voltage (V) Current (A) Power (kW) LV winding with HV terminals open-circuited: 3810 9.86 8.14 HV winding with LV terminals short-circuited: 920 141 10.3 a. Calculate the cantilever equivalent-circuit parameters as referred to the transformer high-voltage winding. b. Calculate the…
A 50-KVA 2400:240-V 60-Hz distribution transformer has a leakage impedance of 0.72 + j0.922 in the high-voltage winding and 0.0070+ j0.0090 $2 in the low-voltage winding. At rated voltage and frequency, the impedance Z, of the shunt branch (equal to the impedance of R. and jXm in parallel) accounting for the exciting current is 6.32 + j43.7 52 when viewed from the low-voltage side. Draw the equivalent circuit referred to (a) the high-voltage side and (b) the low-voltage side, and label the impedances numerically.
Do the following: Solve for the voltage across the appliance and the current through it by referring the appliance to the transformer primary. (Assign the convenience outlet voltage as the reference phasor i.e. at 0o) Draw the circuit that would solve for VL and IL. Compute all referred values and label all components. Solve for VL and IL
1. A 10 kVA, single-phase, 2400-V:120-V, 60 Hz transformer has an equivalent impedance referred to LV side of 0.01 + j0.09 Q. This transformer has a core loss of 100 W at rated voltage. When rated current is applied to the 2400-V winding, the exciting current in that winding is found to be 0.2 A. a. Find the full-load regulation of this transformer at a power factor of 0.8 lagging. b. Find the efficiency of this transformer at full load, 0.8 power factor lagging. c. If standard open-circuit and tests were performed on this transformer, what would be the measured values of these tests? 2. The following data were obtained on a 2.5 MVA, 50-Hz, 19.1-kV:3.81-kV single-phase transformer tested at 50 Hz: Voltage (V) Current (A) Power (kW) LV winding with HV terminals open-circuited: 3810 9.86 8.14 HV winding with LV terminals short-circuited: 920 141 10.3 a. Calculate the cantilever equivalent-circuit parameters as referred to the transformer high-voltage winding. b. Calculate the cantilever…
6- A 600 kVA, 1-ph transformer has an efficiency of 92 % both at full- load and half-load at unity power factor. Determine its efficiency at 60 % of full load at 0.8 power factor lag.
A center-tapped transformer has the schematicrepresentation shown in Figure. Theprimary-side voltage is stepped down to twosecondary-side voltages. Assume that each secondarysupplies a 5-kW resistive load and that the primary isconnected to 120 V rms. Finda. The primary power.b. The primary current.
1. A 10 kVA, single-phase, 2400-V:120-V, 60 Hz transformer has an equivalent impedance referred to LV side of 0.01 + j0.09 Q. This transformer has a core loss of 100 W at rated voltage. When rated current is applied to the 2400-V winding, the exciting current in that winding is found to be 0.2 A. a. Find the full-load regulation of this transformer at a power factor of 0.8 lagging. b. Find the efficiency of this transformer at full load, 0.8 power factor lagging. c. Ifstandard open-circuit and tests were performed on this transformer, what would be the measured values of these tests?
6.5% ans ex A so kvA. 2o00/20 V, So He single-phase transformar has impedance drof of8% and resistance drop of 4%. Caleulate. The Requlation of the Thams former at full- Load o8 P.s Legging. also find The Power factor at which Voltage requlation will Be Zero. Sols 0.5 leading. s alculate The % Noltege Requlation af atransformar in w hich the Percantage resistance drof is 1% and Percentage dre is 6% when The Power fador is 0.8 lagging ) > unity aMS 38 % ans 1 % (シ→ 0.8 leading . amS - 2.2%