find mach and reynolds number and write out N-S eqns oblelahomework, answer the foll4 points): Calculate the Reynolds Number at M = 2 and find the velocity inlet bound-ary condition.(b) (3 points): Write down the Navier-Stokes equations.contour plot (scalarsenal of Mach number and absolute pressure.

Answered: oble la homework, answer the foll 4…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

i didnt understand 3 fluid mechanics questions. please help me :) i will send of the three part
Please show solutions clearly, thank you
The velocity field for a line vortex in the r?-plane is given byur = 0 u? = K / rwhere K is the line vortex strength. For the case with K = 1.5 m/s2, plot a contour plot of velocity magnitude (speed). Specifically, draw curves of constant speed V = 0.5, 1.0, 1.5, 2.0, and 2.5 m/s. Be sure to label these speeds on your plot.
Hint: take partial derivatives of the given shallow water equations and subtract them, e.g. d(eq2)/dx - d(eq1)/dy, and look for bits that make up vorticity, vorticity advection and divergence
1. The Stokes-Oseen formula for drag force Fon a sphere of diameter D in a fluid stream of low velocity V, density p, and viscosity u is: 9T F = 3TuDV + 16PD? Is this formula dimensionally homogenous? 2. The efficiency n of a pump is defined as the (dimensionless) ratio of the power required to drive a pump: QAp input power Where Q is the volume rate of flow and Ap is the pressure rise produced by the pump. Suppose that a certain pump develops a pressure of Ibf/in? (1ft = 12 in) when its flow rate is 40 L/s (1L =0.001 m). If the input power is 16hp (1hp = 760 W), what is the efficiency?
a) Consider two flow situations where water flows between twoinfinite parallel plates seen in top image. Case 1: The top plate moves and thebottom plate is stationary. Case 2: Both plates are stationary. Whatdiffers if Navier-Stokes is applied to both cases to solve for the x-component of velocity? A. equations in the x-directionB. equations in the y-directionC. the boundary conditionsD. the shear stress terms b) In a three-dimensional flow system of an incompressiblefluid, the x-component velocity, vx , is 6xy^2 and the y-component velocity, vy , is -4y^2z. Which is the z-componentvelocity, vz? c is an arbitrary constant. (See bottom image)A. 4yz^2B. 4yz^2 – 6y^2z + cC. 8yz – 6y^2D. 8yz – 6y^2 + c
Find the vorticity of the fluid motion for the given velocity com- ponents. KINEMATICS OF FLUIDS (a) u A(x + y), v = - A(x + y) (b) u = 2Axz, (c) u Ay²+ By + C, v = A(c² + x² - z²) 1)=0
Q2:: Discuss the usefulness of Navier-Stokes equation with the help of practical examples.
An incompressible velocity field is given by u=a(x°y²-y), v unknown, w=bxyz where a and b are constants. (a)What is the form of the velocity component for that the flow conserves mass? (b) Write Navier- Stokes's equation in 2-dimensional space with x-y coordinate system.
4s-1, Given the velocity field V = Axî – Ayĵ, where A %3D (a) Sketch the velocity field. (you can do this by hand or use software of your choice)
can someone explain why P is a function if time only for this question
is called a cone-plate viscometer A solid cone of angle 2k, base 1, and density p, is rotat- Ing with initial angular velocity my inside a conical.seat, as shown in Fig. of viscosity u. Neglecting air drag, derive an analytical ex- pression for the cone's angular velocity ) if there is no applied tongue. The device in Fig. The angle of the cone is very small, so thiat sin 0 0, and the gap is filled with the test liquid. The torque M to rotate the cone at a rate 1 is measured. Assuming a lin- ear velocity profile in the fluid film, derive an expression for tiuid viscosity u as a tumction of (M, R. S2, 0). The clearance h is filled with nil Bave C co radius a dwit) dt Fluid I manmot 1Inentia Derive an expression for the capillary height change h for a fluid of surface tension Y and contact angle 0 between two vertical parallel plates a distance W apart, as in Fig. . What will li be for water at 20°C if W = 0.5 mm? A thin plate is separated from two fixed plates by very vis- cous liquids…

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

oble la homework, answer the foll 4 points): Calculate the Reynolds Number at M = 2 and find the velocity inlet bound- ary condition. (b) (3 points): Write down the Navier-Stokes equations. contour plot (scalarsenal of Mach number and absolute pressure.