NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Refrigerant-134a enters the coils of the evaporator of a refrigeration system as a saturated liquid-vapor mixture at a pressure of 140 kPa. The refrigerant absorbs 200 kJ of heat from the cooled space, which is maintained at -10°C, and leaves as saturated vapor at the same pressure. Problem 07.025.b - Entropy change of the cooled space in an evaporating process Determine the entropy change of the cooled space. (You must provide an answer before moving on to the next part.) The entropy change of the cooled space is [ kJ/K.

NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Refrigerant-134a enters the coils of the evaporator of a refrigeration system as a saturated liquid-vapor mixture at a pressure of 140 kPa. The refrigerant absorbs 200 kJ of heat from the cooled space, which is maintained at -10°C, and leaves as saturated vapor at the same pressure. Problem 07.025.b - Entropy change of the cooled space in an evaporating process Determine the entropy change of the cooled space. (You must provide an answer before moving on to the next part.) The entropy change of the cooled space is [ kJ/K.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter9: Refrigerant And Oil Chemistry And Management-recovery, Recycling,

Section: Chapter Questions

Problem 17RQ: What is the name of the conference that was held in Canada in 1987 to attempt to solve the problem...

See similar textbooks

Related questions

Q: 2. A rigid tank initially contains 2.75 L of air at 125 kPa and 27°C. An electrical resistance…

A: The volume of the tank is V=2.75 L The initial temperature is T1=27°C=300 K. The initial pressure is…

Q: single effect evaporator is being used to concentrate 8000 kg/h of tomato juice from 5% total solids…

Q: A Freon 12 vapour compression system operating at a condenser temperature of 40°C and an evaporator…

A: Given dataTe=0°CTc=40°CRC=15 tonsTo find 1. m°2. discharge temp Tb

Q: What is an adiabatic process?

A: ADIABATIC PROCESS An adiabatic process is a heat transfer-free process from the system or from the…

Q: 0.2 A condenser condenses 2700kg steam per hour while air leaks into It at 2.2kg/hr. The condensate…

A: Given: The steam condenses per hour, mw = 2700 kg/hour The air leakage into the condenser, ma = 2.2…

Q: A tank whose volume is unknown is divided into two parts by a partition. One side of the tank…

Q: Refrigerant-134a is throttled from the saturated liquid state at 800 kPa to a temperature of -20°C.…

A: Given Pressure, P1 = 800 kPa Temperature, T1 = - 20oC Find Final pressure, P2 Final…

Q: 1. Consider filling a "type A" gas cylinder from with water from a high-pressure supply line as…

Q: Problem 08.036E-DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS - Refrigerant Constant Volume System…

Q: A throttling calorimeter is used was used to determine the quality of steam supply. It was found…

A: Given Data: The pressure before throttling is P1 =1.1 MPa. The pressure after throttling is P2…

Q: An insulated tank that contains 2.6 kg of O2 at 15°C and 300 kPa is connected to a 2-m³ uninsulated…

A: Given data as per the question Mass of Oxygen =2.6 kg The initial temperature of oxygen =150 c The…

Q: Steam enters the condenser of a steam power plant at 30 kPa, a quality of 91 % and a mass flow rate…

A: . .

Q: A vapour compression refrigerator circulates 4.5 kg of NH3 per hour. Condensation take place at 30°C…

A: From the given data,

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A: Given: The air compressed by compressor m=10 Ls The pressure at inlet P1=120 kPa The temperature at…

Q: Refrigerant-134a at 800 kPa and 25°C is throttled to a temperature of -14°C. Determine the pressure…

A: Given data, Initial pressure, P1 =800 KPa Initial temperature, T1 = 25°C Final temperature, T2 =…

Q: A rigid tank of 0.22-m'volume initially contains saturated vapor refrigerant-134a at 1.2 MPa. The…

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

Q: A schematic of a steam power plant is shown in the figure. The boiler volume is 50 liter and…

Q: 15- R134a enters a compressor with a heat loss of 200 W as saturated steam at -24 ºC and after…

A: Solution : from the properties of R-134 a @-24°C density of gas =5.76162 kg/m3

Q: 3. Air enters the compressor of a gas-turbine plant at ambient conditions of 100 kPa and 25°C with a…

Q: A reheat cycle with two stages of reheating is executed with steam expanding initially from 25 MPa…

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

Q: Refrigerant 134a enters the condenser of a residential heat pump at 900 kPa and 40 degrees C at a…

A: Assumption:Pump operate in steady stateKinetic and potential energies are neglected. Solution:Draw…

Q: The steam at a pressure of 100 bar and 500°C is supplied to a steam turbine. It comes out at 0.07…

Q: Air at 20 ° C and 50% RH is channeled into the heating coil so that the temperature of the dry ball…

A: Given data:

Q: (1) In an ammonia refrigeration system, the capacity is 210 kW at a temperature of-20°C. The vapor…

Concept explainers

Mechanisms of heat transfer

Heat transfer is an essential discipline in thermal engineering that deals with the transfer, conversion, usability, and creation of heat or thermal energy. Transfer of heat occurs through various mechanisms like conduction, convection, radiation, and change of phases. All these mechanisms have distinct characteristics, but these mechanisms can simultaneously occur in an identical system.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

i-Use the first law of thermodynamics to determine an algebraic equation for the combustorexit temperature (T 04 ) in terms of equivalence ratio (phi) if the fuel in Problem 2 is used. Hint:find the equation for f in terms of T04 and T03 in the canvas handout, our class notes, or in thetextbook in Chpt 5. Then solve that equation for T04 .Assume that the compressor exit temperature T 03 is 650 K. The heating value (Q R ) of thenew fuel in problem 2 is 39,000 kJ/kg fuel. The effective heat capacity cp of the mixture is constant and is 1.2 kJ/(kg-K). Insert these values into your equation for (T 04 ) in terms ofequivalence ratio (phi) ii-Now consider values of fuel-air equivalence ratios (phi) of 0.1, 0.2, 0.3, 0.4, 0.5. Use Matlab,Excel or some other program to use your equation from problem 2 to plot a graph of T04versus f. You have just computed the “adiabatic flame temperature”; the turbojet / turbofan engine designer can decide what fuel-air ratio to use to achieve the desired…
PLEASE DO NOT USE PSYCHROMETRIC CHART. THANK YOU In the diagram below inlet air is drawn over a pool of liquid water in a steady-state, steady-flow isobaric process. Evaporation on the pool resultsin saturated air at the exit. The pool of liquid water is assumed to be at the same temperature as the exitair. Discharge fans at the exit provide a volumetric flow rate of 800,000 ft3/min. Problem #2: Assume that the R134a chiller is turned off such that Qout = 0, but the evaporative coolersystem continues to operate. Determine:a) The exit temperature, T2 (°F)b) The mass flow rate dry air through the system (lbm/sec).c) The rate of liquid water resupply required for continuous operation (lbm/hour).
intake valve intake compression JO BI Tuel injector the temperature of the gas; power exnaust vaive 0010 exhaust The diagrams show the cylinder of a petrol engine in 4 stages. Petrol vapour and air are drawn into the cylinder, The mixture is then squeezed together, and then exploded by a spark. The explosion pushes down the piston. The exhaust gases are then expelled from the cylinder. Use the first law of thermodynamics to analyse the energy changes during the process. At each stage explain what happens to i) the pressure of the gas; ii)
4
VAPOR COMPRESSION REFRIGERATION SYSTEM ANALYSIS 3 Warm environment Он Condenser Expansion valve Evaporator QL Cold refrigerated space in Compressor 1 FIGURE 1: VAPOR COMPRESSION REFRIGERATION CYCLE The chiller system operates based on the vapour compression refrigeration cycle (figure 1) with a single stage compression. The isentropic efficiency of the compressor is assumed at 85%. The refrigerant exit evaporator and condenser can be assumed as saturated.
I need unique and correct answer. Don't try to copy from anywhere. Do not give answer in image formet and hand writing
جية - A - Northern Technical University Technical Eng. College/Kirkuk Fuel and Energy Eng. Tech. Dep. 4th Year Students Final Examination (2022-2023) Subj.: Process of unit operation Date: 6/6/2023 Time: 3 Hours: Morning & Evening Study Note/Answer only four questions, including the first question Q.1: Water is to be cooled in a packed tower from 330 to 295 K by means of air flowing counter currently. The liquid flows at the rate of 275 cm³/m² s and the air at 0.7 m³/m² s. The entering air has a temperature of 295 K and a humidity of 20%. Calculate the required height of tower and the condition of the air leaving at the top. The whole of the resistance to heat and mass transfer can be considered as being within the gas phase and the product of the mass transfer coefficient and the transfer surface per unit volume of column (ha) may be taken as 0.2 s¹. Assuming, the latent heat of water at 273 K = 2495 kJ/kg, specific heat capacity of dry air = 1.003 kJ/kg K, specific heat capacity of…
### Develop the objective for a project report of a cell for the energy reuse of superheated steam within a thermoelectric power plant. The main focus is to determine the pressure drop within the system of this cell and the hydraulic compression pump contained within it. The cell contains, in all, the following equipment: Upstream: Two (tap) switching valves Two eccentric gearboxes Two pressure gauges Downstream: Two pressure gauges Two concentric magnifications A check valve (ball) A (tap) shut-off valve An expansion joint
INTRO THERMODYNAMIC (MAE 91/115) Moran, Shapiro, Boettner, Bailey, Fundamentals of Engineering Thermodynamics, 9e ctice Assignment Gradebook Downloadable eTextbook nment ВАСK NEXT MESSAGE MY INSTRUCTOR FULL SCREEN PRINTER VERSION Problem 12.033 SI As shown in the figure below, moist air at T1 = 36°C, 1 bar, and 35% relative humidity enters a heat exchanger operating at steady state with a volumetric flow rate of 10 m5/min and is cooled at constant pressure to 22°C. Ignoring kinetic and potential energy effects, determine: (a) the dew point temperature at the inlet, in °C (b) the mass flow rate of moist air at the exit, in kg/min (c) the relative humidity at the exit. (d) the rate of heat transfer from the moist air stream, in kW. (AV, T P1 1 bar =35% 2 Т, 322°C P2 1 bar Step 1 Determine the dew point temperature at the inlet, in °C T1,dp ос = Open Show Work Click if you would like to Show Work for this question: y Policy © 2000-2019 John Wiley & Sons, Inc. All Rights Reserved. A…
An air conditioning unit is shown in figure 1, where air enters from left to right.The initial Pressure, Temperature and Relative Humidity data is displayed on the left (INPUT) and the Pressure, Temperature and Relative Humidity data is displayed on the right (OUTPUT).Calculate the heat transfer per unit kilogram of dry air, assuming that the kinetic energy changes are negligible.Note also that condensate is being produced at an indicated temperature.
! Required information Problem 13.058 - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. An insulated rigid tank is divided into two compartments by a partition. One compartment contains 7.0 kg of oxygen gas at 40°C and 100 kPa, and the other compartment contains 4 kg of nitrogen gas at 20°C and 150 kPa. Now the partition is removed, and the two gases are allowed to mix. 0₂ 40°C 100 kPa N₂ 4 kg 20°C 150 kPa -Partition Problem 13.058.b Mixture Pressure Determine the mixture pressure after equilibrium has been established. The universal gas constant is R₁ = 8.314 kPa-m³/kmol-K. Use the table containing molar mass, gas constant, and critical-point properties. The mixture pressure after equilibrium has been established is kPa.
! Required information Problem 13.058 - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. An insulated rigid tank is divided into two compartments by a partition. One compartment contains 7.0 kg of oxygen gas at 40°C and 100 kPa, and the other compartment contains 4 kg of nitrogen gas at 20°C and 150 kPa. Now the partition is removed, and the two gases are allowed to mix. N₂ 4 kg 40°C 20°C 100 kPa 150 kPa →Partition 0₂ Problem 13.058.a Equilibrium Temperature Determine the mixture temperature. Use the table containing the ideal-gas specific heats of various common gases. (You must provide an answer before moving on to the next part.) The mixture temperature is °C.