A throttling calorimeter is used was used to determine the quality of steam supply. It was found that the pressure before and after the throttle were 1.1MPA and 0.11MPA respectively. The temperature after throttling was 115 °C. Determine the dryness fraction of the steam supply. For above pressures, determine the least dryness fraction the steam may have order that its value may determine. Take the specific heat of superheated steam as 2kJ/kg K. (0.936;0.95) 13.

A throttling calorimeter is used was used to determine the quality of steam supply. It was found that the pressure before and after the throttle were 1.1MPA and 0.11MPA respectively. The temperature after throttling was 115 °C. Determine the dryness fraction of the steam supply. For above pressures, determine the least dryness fraction the steam may have order that its value may determine. Take the specific heat of superheated steam as 2kJ/kg K. (0.936;0.95) 13.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

what is the developed boiler horsepower if the steam rate is 0.85 kg/s and the factor of evaporation is 1.25? thank you!
COMPLETE SOLUTION. FINAL ANSWER ARE IN ENGLISG SYSTEMS. DRAW A DIAGRAM IF NECESSARY. Engine XYZ is designed to be operated on the following temperature limits: 80 deg Fahrenheit and 750 deg Fahrenheit. At the beginning of the isothermal expansion the pressure is 350 psia and at the end of the isothermal expansion the pressure is 190 psig. Determine (a) the volume at the end of the isothermal compression, (b) the change of entropy during an isothermal process, (c) the heat added and the rejected, (d) the thermal efficiency, (d) the work developed in BTU/s, and (e) the mean effective pressure.
26. For a compression ratio of 4.56 (V/V2), determine the final temperature of air inside the close piston cylinder assembly if the initial condition is at STP. Final pressure is 847.75kPa a. 273.8926°C b. 271.5038°C c. 279.1343°C d. 277.9285°C
The air in a theatre room must be 22 °C and the relative humidity 55%. The outdoor temperature is 30 °C and relative humidity 50%. There are 900 seats in the room and 25 m³/h of fresh air is reserved for each seat. Every attendant releases a heat load (sensible + latent) of 100 W and a moisture load of 80 g/h. The sum of heat loads from other than human sources is 20 kW. What must the supply air state be in order to maintain the indoor conditions mentioned above?
A reheater cycle with two stages of reheating is executed with steam expanding initially from 20.356 Mpa and 540 oC. The pressures of two reheaters are 3.2356 Mpa and 0.85356 Mpa, and the steam leaves each reheater at 540oC. Condensation occurs at 70oC. Calculate W, ec and ee.
It's clearly Visible Do not Reject
HVAC UPVOTE WILL BE GIVEN. ANSWERS ARE GIVEN ALREADY. PLEASE WRITE THE COMPLETE SOLUTIONS. A room contains air at 20°c (Psat = 2.339 kPa) and 98 kPa at RH of 85%. Determine the following: a) Partial Pressure of dry air. (Ans. 96kPa) b) Specific Humidity of the air (Ans. 0.013) c) Specific Enthalpy per unit mass of dry air (Ans.000 52.81)
QUESTION 27 A four-stage single-acting air compressor running in an atmospheric at 87 kPa and 15°C has a F.A.D of 2.83 m³/min. The section pressure and temperature are 80 kPa and 32 °C respectively, the delivery pressure is to be 7 MPa. The temperature at the start of compression in each stage is 32 °C, take n=1.3 for all stages. With reference to formula file the applicable formual number to find the mass flow rate and power input is and , respectively. The mass flow rate to 3 decimal places in kg/min and power input in kW to 1 decimal place are: , and , respectively. No need to add units
Read the questions carefully before answering. Box or indicate your final answers when solving and draw your diagrams cleanly. Use the steam tables provided and DO NOT ROUND the values from the steam table. Write down the values taken from the steam table. Air undergoes Isothermal expansion in a Carnot cycle where the pressure decreases from 2.5 MPa to 1.5 MPa. This process has a temperature of 550 K and it decreases to 400 K before the Isothermal compression stroke. Find a.) Qa, b.) Qr, c.) Wnet(kJ/kg),d.)the efficiency(%), e.) draw the T-S diagram with proper label of points, and f.) the pressures before and after Isothermal compression •71.55 kJ/kg, 61.78 kJ/kg, 9.77 kJ/kg, 13.65%, 251.52 kPa and 502 kPa •80.66 kJ/kg, 58.66 kJ/kg, 22 kJ/kg, 27.27%, 492.08 kPa and 820.13 kPa •61.22 kJ/kg, 41.22 kJ/kg, 20 kJ/kg, 29.98%, 315.1 kPa and 795.55 kPa •1000 kJ/kg, 900 kJ/kg, 100 kJ/kg, 10%, 500 kPa and 1000 kPa
For a compression ratio of 4.56 (V1/V2), determine the final temperature of air inside the closepiston cylinder assembly if the initial condition is at STP. Final pressure is 847.75kPa a. 273.89260C b. 271.50380C c. 279.13430C d. 277.92850C
A power plant was analysed based on Carnot cycle, the evaporator supplie 553 kJ of heat per cycle at 522°C and condenser cooling fluid was maintained1- at 26°C. Determine the thermal efficiency of this Carnot engine in percentage? Provide answer to 1 decimal place and insert the unit symbol. 1 °C is 273K in this question if required.
Fill in the blanks The ratio of volume at the end of expansion to the volunbe lat beginntng of expansion is 12. Determine the theoretical maximum possible air-standard efficiency assuming the process to be isentropic **Express final answer to the NEAREST WHOLE NUMBER. Do not round ofA in between solution. Type only the 'numerical value". No need to include the unit and percent sign. Answen