Need handwritten pen and paper solution do not use chatgpt or AI otherwise downvote. An AC motor with impedance Z₁ = 4.2 + j3.6 ohm is supplied from a source of 220 V at 60 Hz. Find: a) pf, P and Q, b) Determine the capacitor required to connect in parallel with the motor so that the power factor is corrected and equal to 0.98 behind.

Need handwritten pen and paper solution do not use chatgpt or AI otherwise downvote. An AC motor with impedance Z₁ = 4.2 + j3.6 ohm is supplied from a source of 220 V at 60 Hz. Find: a) pf, P and Q, b) Determine the capacitor required to connect in parallel with the motor so that the power factor is corrected and equal to 0.98 behind.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Similar questions

The winding of a 4-pole alternator having 36 slots and a coil span of 1 to 8 is short-pitched by ........... degrees. 150 40. 90 20 Brushless excitation system consisting of: Stator field winding and power diodes stator and rotor field winding and capacitor stator and rotor field winding and power diodes Everything mentioned in the options Full Name : *
A 40kW induction motor with a lagging power factor of 0.76 is supplied by a 120Vrms 60Hz sinusoidal voltage source. find the capacitance needed in parallel with the motor to raise the power factor to (a) 0.9 lagging and (b) 1.0
Suppose we have an ac current flowing through a coil wound on an iron core. Name two mechanisms by which energy is converted to heat in the core material. For each, how is the core material selected to minimize the power loss? How does each power loss depend on the frequency of the ac current?
Full solutions for the question with explanation
Two identical 2,000 kW alternator operates in parallel. The governor of the first machine is such that the frequency drops uniformly from 50 Hz at no-load to 48 Hz at full-load. The corresponding uniform speed drop of the second machine is 50 Hz to 47.5 Hz. What is the maximum load that can be delivered without overloading either machine?
A 40 kW induction motor, with a lagging power factor of 0.76, is supplied by a 120 V rms 60 Hz sinusoidal voltage source. Find the capacitance needed in parallel with the motor to raise the power factor to: (a) 0.9 lagging, and (b) 1.0.
Can you solve the question ?
The step down DC chopper uses DC source voltage V(dc) = 200 V and resistive load impedance of 10 ohm. The duty cycle is 0.4 the voltage drop across the switch may be taken as zero, Calculate : (a) Average and RMS value of output voltage. (b) Average and RMS value of output current.
Q4/B/ What are the principal characteristics of a series DC motor? What are its uses? Core Mc
a.) full loadb.) half load
(B)-Explain by drawing the change in the direction of current flows through coils at the ideal case of commutation by considering coil B which is the coil under commutation as shown in the figure below. B C 5A SA 5A Armature winding 10 A Commutator 10 A Brush
A 6 pole wave wound d.c. shunt generator has 500 conductors. A generator delivers 50 kW of power at 250 voltage at full load. The resistance of the field circuit is 125 2. Actual brush shift is 10°. Then find the demagnetizing and cross magnetizing ampere turns per pole and how many additional turns must be wound on each pole to eliminate the demagnetizing effect.