microfabrication for particle sorting in microfluid devices need : clean room, very expensive , relatively big devices, only available in big labs snd hospitals! not in 3rd countries. ^ this is what i know about... now they are studying the 3D printing for particle sorting for microfſuids! WRITE A COMPARSION ABOUT (comparison study (of micro fabrication Vs. 3D printing) ) in microfluidic devices sorting with refrence if it is possible

microfabrication for particle sorting in microfluid devices need : clean room, very expensive , relatively big devices, only available in big labs snd hospitals! not in 3rd countries. ^ this is what i know about... now they are studying the 3D printing for particle sorting for microfſuids! WRITE A COMPARSION ABOUT (comparison study (of micro fabrication Vs. 3D printing) ) in microfluidic devices sorting with refrence if it is possible

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Discuss the importance of integrated circuits (ICs) in the design and development of microchips. How do ICs enhance the performance and functionality of microchips?
a. There are three temperature regions for our semiconductors, identify and briefly describe the relation of each of these regions with temperature. b. Consider your cellphone CPU, explain the importance of operating it at the temperature range near or at room temperature.
pplease answer all subparts in short for like either dislike
A. Define Commutation. List the method of commutation and explain the external plus commutation method in details. B. Find an expression for output de voltage in single phase fully controlled thyristor rectifier taking the effect of source inductance into consideration. C. Discuss the different modes of operation of thyristor in detials with help of static VI characterstics?
Electrical Engineering A l-phase bridge rectifier has to supply power to a 300 kW, 120 V DC load. A 240 V, 60 Hz AC feeder is available, and it is desired to have peak-to-peak current ripple percentage of 10%. 1) (a) Sketch the schematic diagram for the rectifier circuit. (b) Determine the inductance for inductor and peak inverse voltage for diode used in Q((a). (c) Sketch the output waveform for the rectifier.
Explain the concept of integrated circuits (ICs) and how microchips are a subset of ICs. Provide examples of ICs other than microchips.
D4 D1 + + 1.2K VsN D3 Y D2 9V sin(27 50 t) 1.b) vs frequency is 50 Hz. Why the v frequency is 100 Hz? 1.c) Calculate the average power dissipated on all four rectifier diodes (assume that each diode is ON for exactly one half cycle of Vs for simplicity). 1.d) How much power would have been dissipated on the diodes in total, if the same output waveform was obtained using a full-wave rectifier with a center- tapped transformer?
Please answer the question step by step and please care to explain the question in detailed with your own sentence and explain why you used that formula, calculations etc asap. Thanks in advance.
Can you solve this question by explaining your solution step by step and giving details on the formulas and calculations, please. Thanks a lot. 2) Consider a two terminal semiconductor diode a) Calculate the thermal voltage of a diode at room temperature about 27oC b) Calculate diode dynamic resistance in case of 13 mA diode current. (Boltzman’s constant is 1.38x10-23 J/K, and magnitude of electron charge is 1,6X10-19 C)
CONSIDERING THE RECTIFIER WITH CAPACITIVE FILTER BELOW AND V1 = 120V, 60 HZ WITH RELATION TRANSFORMER OF 6:1 AND RL = 1K OHMS AND ALSO CONSIDER THAT THE DIODE HAS A DROP VOLTAGE OF 0.7 V AND A RIPPLE VOLTAGE OF 10% OF THE OUTPUT PEAK VOLTAGE, CALCULATE: A) THE AVERAGE VOLTAGE AT THE OUTPUT; B) THE CONDUCTION INTERVAL OF THE DIODES; B) THE AVERAGE CURRENT AT THE DIODE; C) THE PEAK CURRENT AT THE DIODE. 6:1 TR D1 120V 60 HZ V2₁ 2 V2₂ 2 D2 OBS.: NO NEED TO CALCULATE THE CAPACITANCE 1K VS RL
What are ASICs (Application-Specific Integrated Circuits), and how do they differ from general-purpose microchips?
Explain the concept of integrated circuits (ICs) and how they relate to microchips. What are the advantages of using ICs in electronic devices?