D4 D1 RL + 1.2K Vs D3 YD2 9V sin(2r 50 t) 1.b) Vs frequency is 50 Hz. Why the v̟ frequency is 100 Hz? 1.c) Calculate the average power dissipated on all four rectifier diodes (assume that each diode is ON for exactly one half cycle of Vs for simplicity). 1.d) How much power would have been dissipated on the diodes in total, if the same output waveform was obtained using a full-wave rectifier with a center- tapped transformer?

D4 D1 RL + 1.2K Vs D3 YD2 9V sin(2r 50 t) 1.b) Vs frequency is 50 Hz. Why the v̟ frequency is 100 Hz? 1.c) Calculate the average power dissipated on all four rectifier diodes (assume that each diode is ON for exactly one half cycle of Vs for simplicity). 1.d) How much power would have been dissipated on the diodes in total, if the same output waveform was obtained using a full-wave rectifier with a center- tapped transformer?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q2:- Find the level of Vo for each circuit shown in the Figure below. Also, determine the status of each diode; if it is forward or reverses biasing. Assume all diodes are silicone with 0.7v drop.
5. The bridge rectifier shown in Figure 2 uses ideal diodes. The input voltage is 24V. Find: a. DC output voltage b. Sketch the output waveform D2 D3 R1 = 12 k2 Da D Figure 2. Circuit for problem 5 and 6 6. If the bridge rectifier shown in Figure 2 is modified using silicon diodes, find: a. dc output voltage b. sketch the output waveform ell ll
Determine Q-point for the diodes in the circuit given below using the ideal diode model where, R1 = 12.2 kΩ, R2 = 16 kΩ, and R3 = 14 kΩ. (Note: Label the diodes from left to right.)
From the diode circuit shown below. If E=40 V and RL=400, determine the current supplied from the battery. the voltage across the load resistance. and the voltage across diode D2 if all the diodes are silicon with an internal resistance of 2 0. RL E= a. The Current supplied by battery is b. The Voltage across Load resistance RL is c. The Voltage across diode D2 is
R₁ 2,0m D₂ $2.5 R₂ www D₁ ☆ Vo Figure 1: Precision Rectifier 1. Characterize the relationship of input vs. output for the circuit in Figure 1. That is, find an expression for . You can use the constant voltage drop model for the diodes. Vi
Consider a peak rectifier fed by a 60-Hz sinusoid having a peak value V₂ = 100 V. Let the load resistance R = 10 ks. Find the value of the capacitance C that will result in a peak-to-peak ripple of 2 V. Also, calculate the fraction of the cycle during which the diode is conducting and the average and peak values of the diode current.
Consider the half-wave rectifier shown below. It needs to deliver 0.1 A and an average of 15 V to a load. The source is 60 Hz and the diode has a 0.7 V drop. The allowable ripple is no more than 0.4 V (2.5%). Find: Peak AC voltage Vm of the source a) b) The minimum value of the smoothing capacitor(s) c) Comment on the type of capacitor and its/their values you would use for this amount of capacitance vs(t) K Load UL
Consider the circuit in the figure below 4:1 120 V rms ooooo gll reelee D₁ L a. What type of circuit is this? b. What is the total peak secondary voltage? D₂ c. Find the peak voltage across each half of the secondary. d. Sketch the voltage waveform across RL. e. What is the peak current through each diode? f. What is the PIV for each diode? RL 1.0 ΚΩ
Consider the diode circuit shown below. If Vs is a sinewave with a peak amplitude of 12 Volts at 60Hz, and diodes D1 & D2 are considered ideal, sketch the appearance of the waveform at node voltage Vout . Sketch the appearance of the waveform at Vout .
Draw the circuit diagram of a single phase full-wave uncontrolled rectifier with R-load. Describe its principle of operation. Draw the waveforms of: input voltage, voltage across the load, current through the diodes and their voltage. Write the expressions for: the average output voltage Vd, the maximum reverse voltage across the diode and the standard transformer power. Describe what the difference will be if a capacitor is added in parallel with the load at the output. 1.
28. A full-wave bridge rectifier with a 120-V rms sinusoidal input has a load resistor of 1K ohms, Find the required power rating of each diode.
. A half-wave rectifier is needed to supply 15-V dc to a load that draws an average current of 300 mA. The peak-to-peak ripple is required to be 0.2 V or less. What is the minimum value allowed for the smoothing capacitance?