CONSIDERING THE RECTIFIER WITH CAPACITIVE FILTER BELOW AND V1 = 120V, 60 HZ WITH RELATION TRANSFORMER OF 6:1 AND RL = 1K OHMS AND ALSO CONSIDER THAT THE DIODE HAS A DROP VOLTAGE OF 0.7 V AND A RIPPLE VOLTAGE OF 10% OF THE OUTPUT PEAK VOLTAGE, CALCULATE: A) THE AVERAGE VOLTAGE AT THE OUTPUT: B) THE CONDUCTION INTERVAL OF THE DIODES; B) THE AVERAGE CURRENT AT THE DIODE; C) THE PEAK CURRENT AT THE DIODE.

CONSIDERING THE RECTIFIER WITH CAPACITIVE FILTER BELOW AND V1 = 120V, 60 HZ WITH RELATION TRANSFORMER OF 6:1 AND RL = 1K OHMS AND ALSO CONSIDER THAT THE DIODE HAS A DROP VOLTAGE OF 0.7 V AND A RIPPLE VOLTAGE OF 10% OF THE OUTPUT PEAK VOLTAGE, CALCULATE: A) THE AVERAGE VOLTAGE AT THE OUTPUT: B) THE CONDUCTION INTERVAL OF THE DIODES; B) THE AVERAGE CURRENT AT THE DIODE; C) THE PEAK CURRENT AT THE DIODE.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

9. The diodes in a bridge rectifier each have a maximum dc current rating of 2 A. What is the maximum value of the dc load current? 10. What is the PIV across each diode of a bridge rectifier with a secondary voltage of 20 V,rms?
Draw the circuit diagram of a clipper that will produce an output waveform below. From the output waveform Voltage A is 6.7 and Voltage B is -9.7 .Input peak-to-peak voltage is given as 20 volts. Assume Silicon diodes are used. 1. For the positive half cycle, the needed battery voltage is........ 2. For the negative half cycle, the needed battery voltage is........
I need the answer as soon as possible
Discussion:- 1- How does a diode work as a voltage regulator? 2- What is a Zener breakdown? 3- What happens to the DC output voltage when the input varies within the limits? 4- Name three other applications of Zener diodes.
1. Determine the diode current (in Ampere) at 90°C for a silicon diode with reverse saturation current of 90 nanoAmpere and an applied forward bias of 0.5 volts. a. The value of k is (put values only) b. The temperature in Kelvin is (put values only, put up to 2 decimal places) c. The diode current (in Ampere) is : (put values only, put up to 6 decimal places)
A sine voltage trace displayed on a screen is shown in figure. The x axis is 1unit=40 ms and y axis is 1 unit=4 v; determine the frequency of the sine wave and plot the waveform if the same is applied to input of a full wave rectifier.
6. A halfwave rectifier(HWR) has an AC input of 14.14Vrms. A Si diode rectifier is connected such that it will conduct during the negative half cyle while a 5K ohm resistor is connected in parallel with the output (Vo).
For a full wave controlled rectifier with pure resistive load (R=100),the supply voltage is (V-50Sin314t). When the firing angle (a =0%) determine the followings: 1) The mean (dc) value of the load current. 2) The RMS value of the load voltage.
1) When is the diode conducting? 2) The maximum current through the load resistor RL is : 3) The maximum reverse voltage across the diode is :
A. Draw the circuit diagram of a clipper that will produce an output waveform below. From the output waveform Voltage A is 4.7 and Voltage B is -5.7.Input peak-to-peak voltage is given as 20 volts. Assume Silicon diodes are used. B 1. For the positive half cycle, the needed battery voltage is: 2. For the negative half cycle, the needed battery voltage is: B. Design a Clamper circuit to produce the given output waveform with output voltage of V1= 2.7 volts and V2= - 17.3 volts. Input voltage is Vin = 10 Volts and Silicon diodes is used. Vin -Vin
Consider a peak rectifier fed by a 60-Hz sinusoid having a peak value V₂ = 100 V. Let the load resistance R = 10 ks. Find the value of the capacitance C that will result in a peak-to-peak ripple of 2 V. Also, calculate the fraction of the cycle during which the diode is conducting and the average and peak values of the diode current.
Solve each one with steps.