Q4. For the following bridge rectifier circuit, draw the output voltage waveform across the load (RL) showing the maximum value. Cakulate the following: a. The average value of the output voltage across the load (R1). b. The rms value of the output voltage across the load (R1). c. The average load current.

Q4. For the following bridge rectifier circuit, draw the output voltage waveform across the load (RL) showing the maximum value. Cakulate the following: a. The average value of the output voltage across the load (R1). b. The rms value of the output voltage across the load (R1). c. The average load current.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
Consider the following circuit diagram. Using practical diode model solve the following items. i. What is the type of rectification in this circuit? ii. Calculate the total peak secondary voltage (Note that “RMS" value is given in the circuit) iii. Sketch the plot of time vs voltage over Load (RL) iv. Find the average voltage over Load. v. Find the maximum current passing over diodes. vi. Find the peak inverse voltage (PIV) over the diodes. vii. Find the minimum fuse current rating for the primary coil. 5:1 D DA 120 V rms D3 D2 RL=10kQ RL out ell lelll
Write the following for a Semiconverter rectifier with RL load: a) Draw the circuit diagram, supply voltage and the output voltage waveform. b) Explain why there is no negative output voltage even without freewheeling diode. c) Derive the expression for average output voltage.
Draw the changes in Vi and Id of the ideal diode half-wave rectifier circuit in the figure. The frequency of the sine signal here will be taken as 50Hz. (Changes in Vi and Id will be drawn!!!)
Q4. For the folowing bridge rectifier circuit, draw the output voltage waveform across the load (RL) showing the maximum value. Calculate the following: a. The average value of the output voltage across the load (RL). b. The rms value of the output voltage across the load (R1.). c. The average load current. d. The rms value of the load current. (Use constant voltage drop model for the Silicon diode) 5:1 110 Vrms
S-2) a) On the bridge type full wave rectifier circuit given in the figure Plot the current paths for each of the +/- alternans. b) The waveform of the Vç output voltage is given in the graphs on the side. Draw it in the blank and calculate the peak value and indicate it in the graph. c) Calculate the effective value of the output voltage. (Vç (eff) =… ..?). Note: Diodes are not ideal. VD = 0.7V.
For the circuit shown below, compute the maximum current through each resistor when terminal A is a) positive and, b) negative. Assume the diodes are ideal. (Will we convert to the RMS value to it's actual value?)
Given the clamper circuit below, assume that the value of R and C are large enough sothe voltage across the capacitor does not change significantly during the interval of time.a. Using the simplified diode model, simulate the action of the circuit when the Silicon diode isin forward and reverse bias condition and measure the corresponding output voltage.b. Draw the complete output waveform of the circuit
Draw the following rectifier circuits with an input voltage of 12 Vrms and an RL=2K. Determine the output voltage and the current in RL. Plot these waveforms indicating the peak values and the time as per calculation. Also solve for the output DC value. Use silicon diode/s in your analysis. Half wave rectifier circuit (include the diode voltage analysis), Full wave bridge rectifier circuit, Full wave rectifier using center tapped transformer
A full-wave bridge rectifier with a 100V rms sinusoidal input has a load resistor of 1 k. a. If silicon diodes are employed, what is the de voltage available at the load? b. Determine the required PIV rating of each diode. c. Find the maximum current through each diode during conduction. D.
Q4/: A full-wave bridge rectifier at (2:3) transformer with a [77 sin(2n x 100 x 10³t)] rms input signal has a load resistor of 3.3k2. Draw the rectifier circuit and: 1. Sketch and determine effective waveform voltage (VL-P) at the load. 2. Determine the required PIV rating of the diode. 3. What input frequency and output frequency ? 4. What is the de voltage available at the load? 5. Explain who could filtering output signal. 6. Draw circuit that give opposite out waveform. 7. Why connect circuit in this form.
Consider the circuit.a. What type of circuit is this?b. What is the total peak secondary voltage?c. Find the peak voltage across each half of the secondary.d. Sketch the voltage waveform across RL.e. What is the peak current through each diode?f. What is the PIV for each diode?