Q2: Attampet with only two:1: Prove that the dynamic resistance of diode is r=26mv/Ip.2:Prove that the ripple voltage of HWR is Vrtrms=Vrms+Vde and the ripple factor of HWR is 121%,H=40.5%.

Answered: Image /qna-images/answer/57fbf318-ed37-4544-b12d-fef994f004aa.jpg

Answered: Q2: Attampet with only two: 1: Prove…

Engineering

Electrical Engineering

Q2: Attampet with only two: 1: Prove that the dynamic resistance of diode is r=26mv/Ip.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Solve it quickly please now
From the diode circuit shown below, If E-40 V and RL=8002, determine the current supplied from the battery, the voltage across the load resistance, and the voltage across diode D2 if all the diodes are silicon with an internal resistance of 1 02. E= D₁ Z D. RL a. The Current supplied by battery is D₂ D3
The input voltage V, is a sinusoidal voltage with maximum value of 6 V If the threshold voltage of the diodes is 0.1 V, plot V. versus V. +10 V 10 k2 v o o vo 10 k2 10 k2 -10 V
Please answer in typing format
Since R1=4.51 Kohm, R2=1.19 Kohm R3=2.74Kohm R4=5.60Kohm VCC=23.00V and diode silicon in the circuit given in the figure, find the current passing through the diode in mA
Using ideal diodes (voltage drop across ideal diodes is zero) and resistors, construct a circuit that results in the following output vs. input voltage characteristics.
1. Determine Vpout for the circuit in below and draw Vauts assume the diode is the silicon type. 10 k +10 V-- V. ov R, 100 k IN914 -10 V- 2. What is the output voltage that you would expect to observe across R, circuit of Figure below? Assume that RC is large enough to prevent significant capacitor discharge. +24 V 10 uF RL 10 kn V. ov. IN914 -24 V
If the positive cycle of the waveform for full wave bridge rectifier , Which of the diodes is working . ..... ...... 10:1 D1 120 V ms Output 60 Hz Puec) RL 220 N D2 1000 µF D1, D2 D3, D2 D4, D2 O D1, D4 not all above O D1, D3 elle
Questions 1 V, is a 60Hz source with a peak voltage VP-120V is feeding a rectifier, assume ideal diode. The load resistance has a value of R= 10 kn. If ripple voltage Vr = 2V, the Diode average current Ipavg is VI Select one: None b. 580mA 850mA O c. Od 245mA O e. 425mA D C C: R www Q+ Vo
Assuming ideal diode the voltage across the resistor R2 in the circuit shown in the Figure is: R1 E = +12V0- 2.2k2 RE1.8kN E, = +4V A 4.0 V 7.6 V 3.6 V D 4.4 V
A silicon diode has an incremental resistance “R”. It is then connected in series with a resistor 25 ohms across a 25V source. If the voltage drop across the 25 ohm resistor is 10 V, what is the value of “R” ?
For the diode circuit to the right 8002 a V 1002 b 40mA 0.001V' a) To the left of points a and b, find the load-line relation by expressing the current, I with voltage, V. HINT: Write KCL equation for the circuit diagram and write I in terms of V from that KCL equation. This will be your load-line equation. b) Assume the diode has the following characteristic, using the load-line relation you found in (a), determine the operating voltage, V and current, I for the circuit. ip (mA) 20 15 10 5 Vp (V) 3.0 0.5 '1.0 1.5 2.0 2.5