For circuit given in Figure 3 use Complete Diode Modeland find the voltage across R1 and R2 and total current flowing in this circuit. Given that diode forward resistance is 15 Ohms for D1 and 10 Ohms for D2, also reverse current flowing acrossD2 is 20 micro Amperes. DI Ri 50 2 www D2 Rz100N www 10 V R3150 2 www

For circuit given in Figure 3 use Complete Diode Modeland find the voltage across R1 and R2 and total current flowing in this circuit. Given that diode forward resistance is 15 Ohms for D1 and 10 Ohms for D2, also reverse current flowing acrossD2 is 20 micro Amperes. DI Ri 50 2 www D2 Rz100N www 10 V R3150 2 www

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For a certain 12 V zener diode, a 10 mA change in zener current produces a 0.05 V change in zener voltage. The zener impedance for this current range is Ca. 50 O b. 10 c.0.10 d. 100
Referring to Figure , you measure the potential at the connection points R1 and R2 of 3 V. If you get a potential of 0 V at the connection point of the diode and R3, what can you do explain about the condition of the circuit?
Assuming ideal diode the voltage across the resistor R2 in the circuit shown in the Figure is: R1 E = +12V0- 2.2k2 RE1.8kN E, = +4V A 4.0 V 7.6 V 3.6 V D 4.4 V
Assuming an ideal diode model for all the diodes in the circuit below, chose the correct state (bias) for each diode. R1 ww 9kQ 1N1199C R2 D1 18kQ 1N1199C V2 12 V R3 1kQ D3 1N1199C R4 D3: On (Forward Bais) D3: Off (Reverse Bais)
Consider the circuit in the figure below 4:1 120 V rms ooooo gll reelee D₁ L a. What type of circuit is this? b. What is the total peak secondary voltage? D₂ c. Find the peak voltage across each half of the secondary. d. Sketch the voltage waveform across RL. e. What is the peak current through each diode? f. What is the PIV for each diode? RL 1.0 ΚΩ
Assuming an ideal diode model for all the diodes in the circuit below, chose the correct state (bias) for each diode. 9kO IN1199C R2 01 18KO IN11990 D3 IN1199C R3 V2 12 V R4 5kQ
According to the figures, the required load for the zener diode to regulate in the circuit is minimum how many ohms is its resistance?
For circuit given in Figure 3 use Complete Diode Model and find the voltage across R1 and R2 and total current flowing in this circuit. Given that diode forward resistance is 15 Ohms for D1 and 10 Ohms for D2, also reverse current flowing acrossD2 is 20 micro Amperes. DI Ri 50 2 ww D2 Re100 오 www 10 V R3150 2
(c) Reverse recovery is a common problem in a diode. It can increase switching losses, increase forward voltage and induce voltage surge. (i) Explain how reverse recovery can increase switching losses in a diode. (ii) Figure Q1(c) shows that characteristic of reverse recovery in a diode. Based on the figure, calculate the peak reverse recovery current I, I (A) dls dt 30 A Q,, 1 us 3 us Figure Q1(c): The characteristic of reverse recovery in a diode
Consider diode circuit shown below with Vcc=5V and V₂ = 3V. U₁A HH +V₂ ū The peak inverse voltage on the diode is close to V₁ V. A Vo
5V 3000 1000 . 2m 1 Si 4000 500 12V The circuit shown in Figure 1 contains a Si diode with a diode resistance on 1000. Use the piecewise linear model to solve the circuit. • How many nodes are in the circuit? • Determine the Thevenin voltage across the diode. Replace the diode with the appropriate model and then solve the circuit to determine the power dissipated by each resistor and the diode.
B. For the circuit shown below, assume that the zener diode has Vz-3.3V and rz=092 when reverse biased, and has a 0.7V drop when forward biased. Fill the following table for values of Vo for different values of input voltage Vi. R1 Vi Vi -8V OV 8V 1k 5V N V2 R21k Vo Vo