A horseshoe player releases the horseshoe at A with an initial speed vo = 40 ft/sec. Determine the ranges for the launch angle 8 for which the shoe will strike the 14-in. vertical stake. Vo=40 ft/sec. 8 3.2' Answers: Lower range: Higher range: 40' i 31.21 i 61.19 B 14" O O < 0 < < 0 < i i 33.7 61.9 O

A horseshoe player releases the horseshoe at A with an initial speed vo = 40 ft/sec. Determine the ranges for the launch angle 8 for which the shoe will strike the 14-in. vertical stake. Vo=40 ft/sec. 8 3.2' Answers: Lower range: Higher range: 40' i 31.21 i 61.19 B 14" O O < 0 < < 0 < i i 33.7 61.9 O

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A Vessel ot yn Yolume contuine.an DiL which wsighs. 30.2KND
The below column (diameter 1 in.) is subjected to a compressive force where the diameter is increased by 0.0001 in. Determine the shear modulus G of the material. Assume that the material behaves elastically with E= 10000 ksi. P=100Kips L- 12' TOSHIBA
The weight of the crate is 50 kg and the spring constant is 200 N/m in DB. Use g= 9.81 m/s2. -2 m- -3 m- B. 2 m www
3 kN/m. EN 8. A Draw Zm. TS.F. 9 B.M.)
What is the diameter of line shaft that transmit 180kw at 25 rps? a . 2.05in b . 3.05 in c. 4.05 in d 5.05 in
0.3 m 10 kN 40 mm 12 mm 150 mm 12 mm 100 mm 1.5 m 200 mm Formal; Tmaks" Cab TL Gyab'G 25 için --(1- 0,630b/a) M,(1y.2-ly.y) + M,l,. z – lzy -y) 14.ly - Iy T VQ It My • d-- 2tA Ox + dy Os-0y cos20 + Tysin20 , Oart- oy, tan20, - 2ry 2 2 sin20 + Taycos20, Omaks.min + r, 2 Tmaks s = Find the shear stress at a state of the n-n section for opposing beam and loading in the figure. O 0,694 MPa O 0.942 MPa O 1.258 MPa O 0.765 MPa O 1.123 MPa
5.G. 3 If a liguid has a 56 of 17 (a) What is the devrsty in Slayf fit ? Slug specific weight in Lbf? (b) What is the specific weight
Determine the relative roughness of cast iron pipe with inner diameter 3.8 inches.
• Part A Draw the shear diagram for the baam. Folow the sign convention. Fig.m 1) Clok on "add Vertioal line off to add dicoontinulty linec. Then ollok on "add cagment" button to add funotions between the lines. Note 1- You chould not draw an "extra" vertical line at the looation of appled moment. Note 2- Be cure to Indicate the oorreot types of the funotione between the linec, eg. fin your ancwer the type of a funotion Ie "Ilnsar inoressing ciope" for the funotion that actually has linear deoreacing clopa, the ancwer wll be graded as Incorrect Uce the button "ohange cagment" f nsoeccary. 0000 15 kN 10 kN/m 20 kN m 2m 1m No cloments selected v N) 30 20 Im) 20 Add discontinulty ines and seloct segments to add to the canvas Submit dg Aer • Part B Draw the momant diagram for the baam. Follow the sign convention. Cliok on "add vertioal line off to add dicoontinulty linec. Then ollok on "add cagment" button to add funotions between the lines. Note 1- The ourve you chooce from the drop-down…
-] hammer is used on domed circular works
C. An eil Subaricant is put between twe. caHxialcylindexs. The Outer.i xatuting..cerithanqular velacity ef 80cy.cles. /sza|.The .Yadiu.ak autex. cylinder. is. 5 cm. and.khe..cleaxance.betweenn. .... ... the toie cylindets is Taie am.b.Caol.calate max.. Temp if To .bath. wad. temmps.are. Fa'c Givem.Vz 0.75 Cmi/.see 1.25g/cm .................... .. 88.cycles..Se.s. .... .....
Where does the Stress concentrations in shafts occur?