* Ce fea dendn D d f N

Q: Please help me with number 9,10 and 16. This is not graded.

A: 9. Length of threads=16.5 10. No. Of threads=20/2.5= 8 16. No. Of threads=20/1.5=13

Q: A 4.020-gram bullet is projected horizontally to a block of timber that rest on a horizontal floor.…

A:

Q: Determire the kind amel amount of Foree Sos N InoN 8 m a) Methord of Joindr hai) Methord of fedion.…

A:

Q: 3. During tug of war, the bicep muscle generated 4k N force that was perpendicular to the forearm…

A:

Q: Given: V = 60 fps, u = 25 fps, ß = 120°. Determine V, in fps. Select one: O a. 31.3 O b. 29.3 O c.…

A: Given data: absolute velocityV=60 fpsvelocity of the bladeu=25 fpsangleβ=120°   Find out: The…

Q: Which et h

A: introduction: Forging is a manufacturing technique that involves pounding, pressing, or rolling…

Q: Lind Osthogonal tsajctosies 6aX whese a pabometeb

A:

Q: A vessel in Latitude 17- 45'N, Sails to Latitude 15 - 15'N, Find the difference o Latitude made?

A:

Q: minimum cllowasle deign dianet

A: Given; A solid circular shaft needs to be designed to transmit;Torque,T=50 N-mAllowable shear…

Q: The Unit of Impulse is given by_. - O a. N/s O b. Ns O c. N/m O d. N

A:

Q: 181-2,4,0)m A0, 0-6) m Dl0,0, -3 )m w •10 KN ト

A: From the free body diagram given, write the tensions in the cables in cartesian vector form by using…

Q: Which of these welds could be analyzed using the AISC Code's "kips per inch" method? (Indicate all…

A: AISC stands for American institute of steel construction.It is basically quality management system…

Q: A power plant turbine releases its discharge into a condenser operating at 20C at 100% saturated…

A: It is given that:condenser temperature is 20°C. Steam enters condenser as 100% saturated vapor.Mass…

Q: Osing tensor notahan expand the equaton Let Ye =aijXs = lij zj

A: For solution refer below images.

Q: 4 mefeor is aout l a gang and is velocity is 4epined by ve t-5, whare is in seconds. Find fre

A:

Q: quèstion 15 The primary purpose of a chipping hammer during welding is to O A. Prevent oxidation and…

A:

Q: A folloing og strer: oR=75 mpa, Oy = 15 mpa てx-355mia amle elemónt is geuljeefed fo the binanial 11

A: Givenσx=75MPaσy=15Mpaτxy=35MPaallowable  shear stress τa=95MPa

Q: how would this look like if written?

A: The feature control frame is required to describe the condition and tolerances of the geometric…

Q: a boe is foaveling parth of How/ong illake par the bus reach la5 on sap a conctant speedf a

A: Given:v=17 m/sS=5 km =5000 m

Q: What is the name of the highlighted symbol?

A: Dear student, I was the only one who solved this question.

Q: 3.A ball is torsed at s0 m/s at an k the maximum range of the ball and lhcight if the ball was…

A:

Q: 1 4 ind the degree of freedom (F) of the mechanism in the figure.

A: Degree of freedom is defined as a number of input required in a mechanism to get the constrained…

Q: 500 kN.m T KN. m/ m В C 2 m 3 m 5 m Q/Find the value of T (kN. m/m) So that the value of angle of…

A: Given Data Angle of twist at D is zero At A is fixed support so the angle of twist at A is zero…

Q: 5. Use superposition to find the deflection of the free end of the cantilever shown below: w lb/ft 2…

A:

Q: The value of outer diameter of a muff will be .. mm, if the shaft diameter of a muff coupling, is…

A: Write the expression for the outer diameter of a muff. Here, d represents the shaft diameter.

Q: 6500 N 4.5 m- 4.5 m - A 1.5 m 2 m E B

A:

Q: AB beam is a W section drawn profile, P= 50 kN, L= 1,25 m ve E= 200 GPa since it is ( Iw= 26,9.106…

A:

Q: A ame etenmant is gabjecfed fo the foleing biraxial of strex: Ox-75 mpa - 15 mpa %3D てx35m sheap…

A: Given:σx=75 MPaσy=15 MPaζxy=35 MPaζ=95 MPa

Q: Please no written by hand solutions Diagonals FR and ( E)/( m)eet at D,bar (DE) is 8cm and bar (FK)…

A: Given: The length of bar DE is 13 cm and the bar FK is 13 cm.

Q: 3. Fxz²i + (1 - 3xy)j + yzk, A. xyi + 2yzj - 3yk B. zi + 2xzj - 3yk C. zi + 2zj3xk D. xi + 2yzj -…

A:

Q: ing 2omm

A: For solution refer below images.

Q: 6-a toy sparechúp is attached by asiring ts a ceiling fan and a the fan atatas the spiceship trauefs…

A:

Q: CHI) plane Cho use your knowledge of Geometry and the Vale a = (7-92 X1000) cm to determine the Sur…

A: There are three half spheres and three 60 degree angle spheresIt is asked to find the surface…

Q: A WAB 3 m B 2 m 60° D C 1.5 m 45°

A: Given,  WAB= 2 rad/s

Q: What are the reaction forces?

A:

Q: A vessel ot yn Yolume contuine.an Dil which waighs. 30.2KN: speutitguteity the Defeemine of o

A: Volume of the vessel, V= 4 m3  weight of the oil W=30.2 kN

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.