Given D 2KN ← 1m P 2 To Determine 0-3 1m (1-7 one • Diameters of the bars is 1mm e 3 3KN Youngs moduuus E= 200 Gpa NoDau Dispuace ments One man

Q: This question is based on flue gas of power plants. There is a gas that is at 20 Mpa pressure in the…

A: In this problem, the time is 1 second so all answers should be in per second.

Q: For the quick-return mechanism shown below, the rod DC rotates with a constant angular velocity of 1…

A: a) Position of Sliding Block C With Respect to A :1. Using the Law of Cosines in triangle ADC, we…

Q: (a) If the maximum temperature is 700 K and VB is 0.2 m³ what is the pressure po? (b) Find WAB and…

A: Given DataVD=8VoT=700KVB=0.2m3

Q: Q. 3) A T-shaped member, AOC, with a mass of 1 kg, shown below, is kept in static equilibrium with a…

A:

Q: If the flow of Q = 0.10 m³/s of water is to be maintained in the system as shown, what power (P)…

A:

Q: Q5: Determine the deflection at a point 1 m from the left-hand end of the beam loaded as shown in…

A: Solution:

Q: 313 Q/ The steel shaft shown in figure below, it rotates at 3 r/s with 30 kW taken off at A, 15 kW…

A:

Q: 2.20 An unmanned satellite orbits the earth with a perigee radius of 10,000 km and an apogee radius…

A:

Q: Q2: Determine the radius of gyration about a polar axis through the midpoint A of the hypotenuse of…

A:

Q: Two large reservoirs contoining water ot 20C ore connected by a pipe, 9.7 m in length ond 3 mom in…

A: Two large reservoirs containing water at 20°C are connected by a pipo, 9.7 m in longth and 3 mm in…

Q: A 15hp motor is used to drive an air compressor. The mechanical and compressor efficiency are 65% &…

A: Power inputShaft power=15 hp=11.2 kW T1=30oC=303 K P2P1=6 ηm=65% ηC=70%

Q: (RIV) 43 axial load (kN) греed (rpm) ne static and dynamic load capacities of the Eng are 50 and 68…

A:

Q: (Q3-A) The water tank in figure below is being filled through section (1) at Weight flow rate…

A: Calculate the inlet mass flow rate at section 1 using the supplied weight flow rate. m˙1=W˙1g Here,…

Q: Write down the conditions to obtain constant angular velocity ratio by double hool joint. Consider a…

A:

Q: Seventy kilojoules of work is done by each kilogram of fluid passing through an apparatus under…

A:

Q: PROBLEM 4: Part a.) Find the centroid of the following area in the x direction. Part b.) Find the…

A: The thickness of web =1 in

Q: Q1.The shaft, as shown in Fig. , is driven by pulley B from an electric motor. Another belt drive…

A: Write the given values along with suitable variables.

Q: 0 Uエ steam with 0.05 oF quality. This stear heated at a constant volume and its Po

A: Given mass=4kgV=5m3x=0.05so ν=Vm=54=1.25m3/kg

Q: The elements of a rear suspension for a front-wheel-drive car are shown in the figure. Determine the…

A: For the given arrangement of rear suspension To determine  Reactions at joint A, B, C, D, E, and F…

Q: A cube of side 21 mm is made of a material with thermal conductivity 182 W m-1 K-1, density 1426 kg…

A: Given:Side of a cube, S=21 mm=0.021 mThermal conductivity of a material, k=182 W/m.KDensity of a…

Q: Determine the location yc of the centroid C of the beam having the cross- sectional area shown. Take…

A: The schematic diagram of the I section of the beam is as follows:

Q: A projectile is shot at an inclination of 45° from the ground with a speed of 250 mps. (a) Derive…

A:

Q: Determine the x- and y-coordinates of the centroid of the shaded area. 0.50 a Answer: (X, F) = ( i i…

A:

Q: 3. A space at sea level is 25°F and RH = 30% Find the other properties of the air in that space. DB…

A: (3) Answer From psychrometric chart:- @ DB = 25F and RH = 30%, we get WB = 18.8 F Humidity= 0.00082…

Q: • Lengths: O2A-4 in., O3B=8 in, BC=5 in, O2O3-4 in. and offset c=10 in. • Angles: 8-60° and = 45°…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: To Determine Angunar veuocity of Arm velocity at Point C

A: Given:Velocity at A  = 14mm/sAB = 25 cmBC = 15 cmTo find:Angular velocity at armVelocity at point…

Q: Q. 2) Given the following system of forces acting on the solid as shown, (a) Determine the…

A: A solid structure is given with force and moments acting as shown.

Q: 6. Obtain the dynamic equation of the system given below in terms of the position of mass M. tew…

A: The study of how moving objects act is known as dynamics. The branch of mechanics that analyzes…

Q: Distilled water with a mass flowrate of 80,000 kg/h enters an exchanger at 35 °C ane leaves at 25…

A:

Q: Consider a structure including the horizontal beam AB hinged to the wall at point A and supported by…

A:

Q: Q4: A composite bar is constructed from a steel rod of 25 mm diameter surrounded by a copper tube of…

A:

Q: Determine work done

A: Given data : Force Applied F=3 N Distance covered d=2 m   To find : Work done