Answered: Maximum allowable stress for steel =…

Maximum allowable stress for steel = 140 MPa Maximum allowable stress for aluminum = 90 MPa Maximum allowable stress for bronze = 100 MPa Required : Maximum safe value of axial load P

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Aluminum Steel hs composite beam of aluminum (F. = 70 GPa) and steel (F. = 190

Q: An aluminum alloy [E = 73 GPa; v = 0.33; a= 23.0 x 10-6/°C] plate is subjected to a tensile load P.…

Q: m

A: Applied tensile load = 330000 N = 330Kn Maximum Allowable Stress = 110 Mpa…

Q: H h d

A: To solve this, we need to find the permissible load at critical section that is at the section where…

Q: Punch Aluminum =4 mm d-20 mm

A: Given that t=4 mmd= 20 mmUltimate shear stress = 280 Mpa

Q: For the state of stress shown, determine (a) the principal stresses, (b) the maximum in-shear…

Q: 2-A teel pod is sfreteked between fwo rigid walls ard carries a tensile Coad f GO00N at C.f the…

Q: A rigid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D, as…

A: The given data is as follows: E=200 GPaAllowable stress in rod CD=124 MPa

Q: A Sandwich block is comprised of brass in the centre with two aluminium plates attached to either…

Q: A 2-m long steel rod, 10-mm in diameter, is carrying a load of 20 kN. (a) what is the axial stress…

A: This question is related to the Strength of material. In this question we calculate axial stress and…

Q: An aluminum alloy [E = 74 GPa; v = 0.33; a = 23.0 x 10-6/°C] plate is subjected to a tensile load P.…

Q: 25 mm PROBLEM 2.49 Brass core The aluminum shell is fully bonded to the brass core and the assembly…

Q: Q.2 The bar is made of an aluminium alloy having a stress-strain diagram that can be approximated by…

A: Solution: Given: Bar is made of an aluminium alloy ∈Max=0.05

Q: GIVEN: Solid aluminum bar shown: 4 in. by 4 in. E = 10 x 10° psi oy = 36 ksi 4000 & 200016 4000 16 B…

A: A) Load in each section of bar PAB = 4000 lb ( T ) PBC = 4000 - 2000 = 2000 lb ( T ) PCD = 4000 -…

Q: An aluminum alloy [E = 69 GPa; v = 0.33; a = 23.0 x 10-6/°C] plate is subjected to a tensile load P.…

Q: A bar obtained by bonding together pieces of steel (E = 29 x 106 psi) and brass (E = 15 106 psi) has…

A: Given : Es = 29 X 106 psi Eb = 15 X 106 psi M = 40 kip-in. This is a problem of Solid mechanics…

Q: A typlcal aluminum-alloy scuba diving tank Is shown. The outside diameter of the tank is 200 mm and…

A: Maximum shear stress in plane = pd/8t Where, d = inner diameter d = 200-2*12 = 176mm

Q: PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the…

Q: The rigid bar of negligible weight is supported as shown. The assembly is initially stress-free.…

Q: calculate the strength reduction factor at the minimum strain of extreme tension steel f'c=28 mpa…

A: Given data: f'c=28 mpa fy=420 mpa

Q: Two cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that the…

Q: A hollow aluminum tube is rigidly attached between steel rod and a bronze rod as shown. Axial loads…

Q: 3. The rigid bar weighs 5 kN/m, is supported as shown. The assembly is initially stress-free. Find…

Q: Determine the force P necessary to close the gap at the steel post. The steel post is 2 inch x2 inch…

A: Given : Steel post dimension = 2 inch X 2 inch Height = 8 inch Width of aluminum alloy bar = 1.5…

Q: The failure stress of a homogeneous steel bar having a diameter of 10 mm is 250 MPa. Using a factor…

Q: Determine the maximum permissible value of T subject to the following conditions: tst < 80 MPa, Tal…

Q: 1.4 Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly…

Q: Bronze Aluminum Steel A=400 mm? A= 600 mm? A=300 mm? 2P ЗР 4P -3 m -5 m 4 m Three round bars welded…

Q: 20 mm 10 mm 10 mm 20 mm 10 mm 10 mm The Aluminum machine part is subjected to a bending moment M =…

A: Given M=75N.m To find Determine (a) distance of neutral axis from the bottom of the cross section,…

Q: A fully bonded aluminum shell and steel inner Outer core bar is axially loaded. Find the normal…

Q: Calculate the stress in the copper bar (in MPa). b)Calculate the axial deformation in the brass bar…

Q: A typical aluminum-alloy scuba diving tank is shown. The outside diameter of the tank is 200 mm and…

Q: (CLO 1, 2)Determine the stress in the Aluminum rod (Psi) after the load 142 (kips) is applied. The…

A: Given Data: The load applied on the beam is, P=142 kips To Determine: The stress in the aluminum…

Q: An aluminum alloy [E = 72 GPa; v = 0.33; a= 23.0 x 10-6/°C] plate is subjected to a tensile load P.…

Q: The structure shown below is hinged to fixed supports at A and C. The bars are each 4 in. by 4 in.…

A: Introduction- A structural support is a component of a building structure which contains the…

Q: Question 4. Three wires are used to suspend the plate shown. Aluminium wires used at A and B with a…

Q: The pin-connected structure consists of a rigid beam ABCD and two supporting bars. Bar (1) is an…

Q: An aluminium wire (E=10,600 ksi) having a diameter d%-1/8 inch. and length L=14 ft is subjected to a…

Q: 2) A solid rod with the given dimension shown in Fig. Axial loads are applied at the positions…

Q: The rigid bar of negligible weight is supported as shown. The assembly is initially stress-free.…

A: Stress at the steel rod

Q: Consider the compound system consisting of three sections with cross-sectional areas 3A, 2A, and A…

A: The correct answer to the given questions are as under

Q: 1. The assembly has the diameters and material makeup indicated. If it fits securely between its…

A: αal=12.8×10-6/°Fαbr=9.6×10-6/°Fαst=9.6×10-6/°FEal=10.6×106 lb/inEbr=15×106 lb/inEst=128×106 lb/in

Q: Compute the maximum force F (in KN) that can be applied to the composite rod if the allowable total…

A: The given figure is shown below:

Q: 2.31 The three symmetrically placed rods support the rigid block of mass M. Before the block was…

Q: A brass (? =5.6 ? 10^6 ???) and aluminum (? = 3.7 ? 10^6 ???) cylinders are bonded together at B,…

A: Note:- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Concept explainers

Material Properties

Construction in civil engineering demands high strength, durability, and longevity. These targets can be achieved by better design and analysis, along with the correct choice of materials. Different materials have different properties and hence, they respond and performs differently under the various condition of external loadings. It is therefore a critical task of an engineer to select the right material based on the property that the material is supposed to function in real-time. When speaking about the property, there are different categories of material properties like chemical property, physical property, mechanical property, electrical property, magnetic property, thermal property, etc. These material properties form the basis of material selection in various applications.

Question

Maximum allowable stress for steel = 140 MPa

Maximum allowable stress for aluminum = 90 MPa

Maximum allowable stress for bronze = 100 MPa

Required : Maximum safe value of axial load P

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

QI/ An aluminum bar carries the axial loads at the positions shown in Fig. 1, below. The diameter for part AB, BC and CD is 35 mm, 40 mm and 30 mm, respectively. The elastic modulus for aluminum is 72.4 x 10 N/mm. Determine the internal stresses at section (A-B), (B-C) and (C- D), and the elongation (AL) in length at each part of aluminum due to loading. в D 37 kN 10 kN 45 kN 18 kN 1000 mm 800 mm I 600 mm Fig. 1
Problem 1 An axial force of P is applied to the center of the rigid end plate shown below. If the portion of the load carried by the aluminum plates is half the portion of the load carried by the brass core, (a) determine the value of h, (b) the total load if the stress in the brass is 50 MPa. Brass core (E = 105 GPa) Aluminum plates (E = 70 GPa) Rigid end plate 300 mm 60 mim 40 mm
The column above is subjected to axial loading only. Assume the following: • E= 29000 ksi G = 10000 ksi • = 986 in4 A = 60 in? • L= 20 ft • Grade 60 steel (60 ksi yield stress) • The column is fixed at the top and pinned at the bottom Which of the following is closest to the maximum normal stress the column can support (before yielding or buckling)? 167 ksi 24 ksi 42 ksi 60 ksi
A circular aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C; v = 0.33] pipe has an outside diameter of 270 mm, a wall thickness of 15 mm, and a length of 5.5 m. The pipe supports a compressive load of 635 kN. After the temperature of the pipe drops 45°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) 8 = i AD= i mm mm
The solid rod has a diameter of 20mm. Find the following: Angle of twist at C with respect to A (in radians) Angle of twist at B with respect to A (in radians) Maximum shear stress at A (in MPa) (Shear stress at support, at a point 7mm from center. (in MPa) A-36 steel with the following properties: Modulus of Elasticity, E = 29x10^3 ksi or 200 GPa Shear Modulus/Modulus of Rigidity, G = 11.5x10^3 ksi or 79.3 GPa Poisson's Ratio, nu = 0.260 Temperature Coefficient for thermal expansion, a = 6.6x10^-6/°F or 11.7x10^-6/°C
The state of plane stress shown occurs at a critical point of a steel machine component. As a result of several tensile tests, it has been found that the tensile yield strength is o, = 250 MPa for the grade of steel used. Determine the factor of safety with respect to yield using (a) the maximum shearing stress criterion, and (b) the maximum distortion energy criterion. ↑y 40 40 MPa 80 MPa 25 MPa ➜X
Aluminum Bronze Steel 2P 3P P 4P - - 1.0 m 0.8 m FIG. P2.16 2.16 A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. Determine the maximum allowable value of P if the change in length of the bar is limited to 2 mm and the working stresses pre- scribed in the table are not to be exceeded. A (mm²) E (GPa) G, (MPa) Вronze 450 83 120 Aluminum 600 70 80 Steel 300 200 140
a) Determine the force P (in kN) required to stretch the Aluminum bar by 3mm. B) Determine the final width and thickness of the Aluminum bar. (1)
Required information Consider the loading shown. The allowable normal stress for the steel used is 160 MPa. 0.8 m 50 kN/m B -2.4 m- 0.8 m For the selected design, determine the actual value of Om in the beam. (Round the final answer to one decimal place. You must provide an answer before moving to the next part.) The actual value of om in the beam is 160 MPa.
The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P = 20 KN is applied. %3D Steel E200 GPa A-600mm L1 m 2.0 m 0.6 m 1.5 m Pa20 KN Aluminum E-70 GPa A=900mm L-1.5 m What is the ratio of the deformation of steel to deformation of aluminum?
The general stress element shown is loaded such that o = 20 MPa, oy = -20 MPa, Txy = 10 MPa. What is the max dy 1 xy 70x
1/2 Problem 1: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown in. If the stress must not exceed 14OMPA in either rod, determine the smallest allowable value of the diameter of rod AB and ВС. 300mm B 40 kN 250mm - d2 30 kN