Complete the table belowDraw the cylindrical mold and include the dimensionsShow the computation of average unit weight only, others not neededITEMTrial Number1234Total Mass of Mold and Aggregate(kg)12.712.7512.6512.8Mass of Mold (kg)4.004,004.004.00Mass of Aggregate (kg)8.70Volume of Mold (cum)0.00556Unit Mass (kg/m³)Unit Weight (kN/m³)Percent difference from averageAverage Unit Weight:kgs/cumDimensions of cylindrical mold6 inches diameter0.1524m12 inches high0.3048m

Answered: Image /qna-images/answer/7444405c-f00b-47ab-bd71-6175e9d9376c.jpg

Answered: Mass of Aggregate (kg) 8.70 Volume of…

Mass of Aggregate (kg) 8.70 Volume of Mold (cum) 0.00556 Unit Mass (kg/m³) Unit Weight (kN/m³) Percent difference from average

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit…

A: The concrete design needs to be like individual codes defining the terms of a complete building…

Q: 1. Fineness modulus of the coarse aggregate Individual Cunulative Seive (nn) Weight Retained Percent…

A: Given data-

Q: The following information is available from a specific gravity test on fine a wt of SSD sand = 509 g…

A: A =weight of oven-dry sandB = weight of pycnometer filled with waterC = weight of pycnometer filled…

Q: A sieve analysis test was performed on a sample of aggregate and produced the results shown in Table…

A: The table is given below,

Q: 5.17 Calculate the sieve analysis of the following aggregate and plot on a semilog gradation paper.…

A: Given datasive size is givenamount retained is givenFindsive analysismaximum sizenominal maximum…

Q: 1. Calculate the solid volume and percent of voids of an aggregate that weighs 111.2 pcf and has a…

Q: 20. Calculate the solid volume and percent of voids of an aggregate that has a density of 1581 kg/m³…

Q: Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit…

A: Given: Volume of bucket, V = 1/3 ft3 Weight of empty bucket, W1 = 18.5 lb Weight of bucket filled…

Q: Q3) The result of sieve analysis of a sample of aggregate given in the Table below. According to…

A: Sieve analysis: It is an analytical method that is used to determine the particle size distribution…

Q: Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit…

Q: Testing Procedure for Unit Weight of Aggregate.

A: ObjectiveDetermine of unit weight of the aggregate Equipment used1) Tamping Rod - Dia of 16 mm and…

Q: 2. A sieve analysis was conducted on an aggregate with a nominal maximum aggregate size of 20 mm.…

A: Soil boundaries give an idea of its compatibility with soil and water or both compounds. When the…

Q: Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit…

A: The given data is: Volume of bucket = 1/2 ft3 Weight of Empty Bucket = 20.3 lb Weight of bucket…

Q: Determine the suitability of the aggregate, with the gradation tabulated below, for use in Portland…

Q: A sieve analysis test was performed on a sample of coarse aggregate and produced the results in…

A: Since we are authorized to attempt only three sub-parts of the given question, we have done first…

Q: Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit…

A: According to given data Coarse aggregate is placed in a rigid bucket (mold) and rodded with a…

Q: A sieve analysis test was performed on a sample of coarse aggregate and pro- duced the results in…

A: The given table is shown below:

Q: 5. Calculate the solid volume and percent of voids of an aggregate that weighs 111.2 pcf and has a…

A: unit wt of the aggregate=111.2 pcfweight of the aggregate for 1 ft3 volume w=111.2 lbspecific…

Q: (14) IfC 400 kg/m; W200 kg/m; Air content 4% and CA (SSD) = 840 kg/m³.Using the volume method, the…

Q: The following table shows the results obtained from laboratory tests done on samples of aggregates.…

A: Answer We are given Bulk specific gravity of SSD = 2.67 Weight of aggregates+metal container ( Wam…

Q: If Slump=120 Maximum size of aggregate=25 How is the amount of water interpolated ?

A: Basically, interpolation of data is done to know the exact value of variable which cant be predicted…

Q: Referring to the aggregate gradations A, B, and C in Figure , answer the following questions:a. What…

A: Consider the figure of aggregate gradations.

Q: Referring to the aggregate gradations A, B, and C in Figure P5.26, answer the following questions:…

A: Given values: Consider the graph given. Maximum size of aggregate is the smallest size of sieve…

Q: The following information is available from a specific gravity test on fine aggregate: wt of SSD…

Q: The mass of a bulk density bucket is measured as 2115 g when it is empty. The mass of the bucket…

A: Given, Mass of empty bulk density bucket (M1) = 2115 g Mass of bucket filled with water(M2) = 5148…

Q: 10. Calculate the solid volume and percent of voids of an aggregate that has a density of 1581 kg/m3…

A: Given:- The density of the soil = 1581 kg/m3 The specific gravity = 2.59 To determine:- The solid…

Q: Determine the suitability of the aggregate, with the gradation tabulated below, for use in Portland…

Q: From the given data shown in the table below, determine the effective specific gravity of…

Q: Based from the proportion that you have designed, say that the concrete is mixed to fill 20 cubes…

A: Given, Cement content = 370 kg/m3 Water content = 195 kg/m3 Fine aggregate content = 490 kg/m3…

Q: 5.10 Samples of coarse aggregate from a stockpile are brought to the laboratory for determination of…

A: Hi! Thank you for the question, As per the honor code, we are allowed to answer three sub-parts at a…

Q: Given for a set of aggregates: A=2030.9, B 2044.9 and C=1304.3 A = Oven dry weight B = SSD…

A: Given, A = 2030.9 g B = 2044.9 g C = 1304.3 g

Q: From the given data shown in the table below, determine the effective specific gravity of…

Q: What is the fineness modulus of this aggregate?

Q: Given the image below. What is the maximum diameter of aggregate considering the narrowest dimension…

A: e = 69cm= 690mm Dia of main bar = 25mm Dia of stirrups = 10mm Assume clear cover = 40mm Clear width=…

Q: 5.24 Three aggregates are to be mixed together in the following ratio: Aggregate A 35% Aggregate B…

A: Given:- Aggregate A-35%Aggregate B-40%Aggregate C-25% To find:- Percent passing each sieve for the…

Q: What is the maximum diameter of aggregate in cm? 160mm slab 130mm beam 17:25pm 500mm 700mm Slab=10m…

A: This question is related to the Design of Concrete Structure.

Q: If needed assume the unit weight of water to be 62.4 lb/ft3 a) A HMAC sample has the following…

A: Note: Hi! Thank you for the question as per the honour code, we’ll answer the first question since…

Concept explainers

Analysis and Procedures for Material Selection

The term material selection means to select the right material for various engineering applications. There are various engineering materials available and each has different individual properties. Thorough knowledge of the material properties and behavior is crucial in the design process. For instance, a structural member, such as a beam, is used to support vertical shear loads by the building itself. To withstand such loads, the material of the beam must possess adequate strength and stiffness to resist any deformation that might lead to the formation of cracks.

Question

Complete the table below
Draw the cylindrical mold and include the dimensions
Show the computation of average unit weight only, others not needed
ITEM
Trial Number
1
2
3
4
Total Mass of Mold and Aggregate
(kg)
12.7
12.75
12.65
12.8
Mass of Mold (kg)
4.00
4,00
4.00
4.00
Mass of Aggregate (kg)
8.70
Volume of Mold (cum)
0.00556
Unit Mass (kg/m³)
Unit Weight (kN/m³)
Percent difference from average
Average Unit Weight:
kgs/cum
Dimensions of cylindrical mold
6 inches diameter
0.1524m
12 inches high
0.3048m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Analysis and procedures for material selection

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is the maximum diameter of aggregate in cm?
If Slump=120 Maximum size of aggregate=25 How is the amount of water interpolated ?
Testing Procedure for Unit Weight of Aggregate.
1. The following data were obtained during a tension test of an aluminum alloy. The initial diameter of the test specimen was 0.505 in. and the gage length was 2.0 in. Load (lb) 0 2 310 4 640 6 950 9 290 11 600 12 600 Elongation (in.) 0.00220 0.00440 0.00660 0.00880 0.0110 0.0150 Load (lb) 14 000 14 400 14 500 14 600 14 800 14 600 13 600 Elongation (in.) 0.020 0.025 0.060 0.080 0.100 0.120 Fracture Plot the stress-strain diagram and determine the following mechanical properties: (a) proportional limit; (b) modulus of elasticity; (c) yield point; (d) yield strength at 0.2% offset; (e) ultimate strength; and (f) rupture strength.
Determine the difference between the Rodded and Loose Unit Weight of aggregates
complete the table and answer quest
What is the maximum diameter of aggregate considering the clear spacing of the reinforcements in mm? 160mm slab Slab=10mm 130mm beam 700mm 17.25cm 500mm 4 Obeam=25mm D =?
Why unit weight of aggregates is important? What should be the best conclusion and result of the aggregates in doing the experiment?
A sieve analysis test was performed on a sample of coarse aggregate and produced the results in Tablea. Calculate the percent passing through each sieve.b. What is the maximum size?c. What is the nominal maximum size?d. Plot the percent passing versus sieve size on a semilog gradation chart.e. Plot the percent passing versus sieve size on a 0.45 gradation chart.f. Referring to Table (ASTM C33), what is the closest size number anddoes it meet the gradation for that standard size?
With aid of diagram, elaborate on the method to test material hardness using Brinell hardness test
5. Calculate the solid volume and percent of voids of an aggregate that weighs 111.2 pcf and has a specific gravity of 2.62.
The following table provides data obtained during a bulk density test on coarse aggregate. Determine the bulk density of the coarse aggregate to four significant figures