What is the maximum diameter of aggregate in cm? What is the maximum diameter of aggregate in cm?Consideringa = 28cmb = 6cmc = 51cme-61cmd-13cmslabbeameOslab=10⁰mObeam=25m

This question is related to the Design concrete structures.

Answered: What is the maximum diameter of…

Engineering

Civil Engineering

What is the maximum diameter of aggregate in cm?

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter2: Soil Deposits-origin, Grain-size, And Shape

Section: Chapter Questions

Problem 2.15CTP: In concrete work, Fuller and Thompson (1907) suggested that a dense packing of grains can be...

See similar textbooks

Related questions

Q: Coarse aggregate placed igid buc its unit weight. The following data were obtained: Volume of bucket…

A: According to given data Coarse aggregate is placed in a rigid bucket (mold) and rodded with a…

Q: bucket and rodded with a tamping rod to determine its unit weight. The following data are obtained:…

A: V=0.3 ft3

Q: How does shape and surface texture of aggregate effect workability, water requirement, and bond in…

A: Concrete is a combination of cement, aggregate, as well as liquid. Aggregate, typically makes up 60…

Q: Discuss five different desirable characteristics of aggregate used in Portland cement concrete (PCC)

A: Here some of the most desirable characteristics of aggregates used in portland cement concrete are…

Q: In designing concrete structures, normally maximum aggregate sizes are adopted with ranges from 10mm…

A: Greater the size of aggregate lesser is the surface area. Lesser is the surface area indicate that…

Q: only as specified by the instruct 5.10 Samples of coarse aggregate from a stockpile are brought to…

Q: 5.10 Samples of coarse aggregate from a stockpile are brought to the laboratory for determination of…

A: Given:- The following weights are found from the sample of coarse aggregates:- Mass of moist…

Q: ! Three 150 mm x 300 mm concrete cylinders with randomly oriented steel fiber contents of 0, 2, and…

A: Area of Specimen, A = π4d2A= π41502 = 17662.5 mm2 1 1 1 2 2 2 3 3 3 Deformation, mm ∆L…

Q: What is your recommendation for the maximum size of situation? A reinforce concrete column with the…

A: GIVEN-Thickness of column=300mm Minimum clear spacing=180 mm Maximum size of…

Q: An exterior beam, located in Toronto, with a rectangular cross section has a width of 1000mm, height…

Q: The mass of a bulk density bucket is measured as 2115 g when it is empty. The mass of the bucket…

A: Given, Mass of empty bulk density bucket (M1) = 2115 g Mass of bucket filled with water(M2) = 5148…

Question

What is the maximum diameter of aggregate in cm?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

a. For an aggregate sample, if you know that the apparent relative density is 2.72 and the water absorption is 1.2%. The dry mass of the aggregate is 514 gm. Find the bulk and saturated surface dry (SSD) relative density values? b. Why does the maximum size of aggregate depend on the clear spacing between bars? Show with a simple sketch. Note: Please answer both a and b... Please answer the both questions.. I don't want single b answer.. thank you
Referring to the aggregate gradations A, B, and C in Figure P5.26, answer the following questions: a. What is the maximum size of each gradation? b. What is the nominal maximum size of each gradation? c. Classify each gradation as dense, open, or gap indicating the reason for each classification. 100 A 80- 60 40 0.075 0.30 1.18 2.36 4.75 9.5 12.5 19.0 25.0 0.15 0.60 Sieve sizes (mm) FIGURE P5.26 Percent passing 20
Testing Procedure for Unit Weight of Aggregate.
Distinguish porosity from voids content for aggregate with the help of schematic diagrams.
Why unit weight of aggregates is important? What should be the best conclusion and result of the aggregates in doing the experiment?
Pls solve fast and correct do not solve wrong
The mass of a bulk density bucket is measured as 2115 g when it is empty. The mass of the bucket when filled with water is 5148 g. The bucket is filled with aggregates and the total mass of the bucket and aggregate is measured as 7073 g. Calculate the bulk density of the aggregate.
Answer question 5.36
Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit weight. The following data are obtained: Volume of bucket ½ ft3 Weight of empty bucket Weight of bucket filled with dry rodded coarse aggregate 20.3 lb Trial 1 = 69.6 lb Trial 2 = 68.2 lb Trial 3 = 71.6 lb a. Calculate the average dry-rodded unit weight b. If the bulk dry specific gravity of the aggregate is 2.620, calculate the per- cent voids between aggregate particles for each trial.
Show the work
Manov Steel Inc. has a rolling mill that produces sheet steel with a nominal thickness of 0.125 inch. Suppose that the specification limits are given by LSL = 0.120 and USL = 0.130 inch. According to historical data, the actual thickness of a random sheet produced by the mill is normally distributed with mean and standard deviation of u = 0.125 and o = 0.0025. (a) What are the lower and upper natural tolerance limits (LNTL and UNTL) for individual sheets of steel? (b) What are the lower and upper control limits (LSL and USL) if we use a control chart that plots the average thickness of samples of size n = 4? (c) What will be the percentage nonconforming, given the above values for (LNTL, UNTL) and (LSL, USL)? What is the process capability index C? Do you consider this process capable of meeting its performance specifications? (d) Suppose that the process mean suddenly shifts from 0.125 to 0.1275. What happens to the process capability index C and the percentage nonconforming?
Kindly give me right solution. Don't copy from other experts solution.