Based from the proportion that you have designed, say that the concrete is mixed to fill 20 cubes (100 x 100 x 100mm) and 10 prisms (500 x 100 x 100mm), find the mass of each material based on the aggregate conditions in Table 2. QuantitiesPer m³ (to nearest 5 kg)Per trial mix ofm³Cement (kg)370Water (kg or litre) Fine aggregate (kg)195490Coarse aggregate (kg)10mm 20mm 40mm1310 ItemCoarse aggregateSandTable 2 Aggregates ConditionDetailsAbsorption capacity 1.2 %Free moisture 2.0%Absorption capacity 1.5%Moisture content 3.0%

Given, Cement content = 370 kg/m3 Water content = 195 kg/m3 Fine aggregate content = 490 kg/m3…

Based from the proportion that you have designed, say that the concrete is mixed to fill 20 cubes (100 x 100 x 100mm) and 10 prisms (500 x 100 x 100mm), find the mass of each material based on the aggregate conditions in Table 2.

Based from the proportion that you have designed, say that the concrete is mixed to fill 20 cubes (100 x 100 x 100mm) and 10 prisms (500 x 100 x 100mm), find the mass of each material based on the aggregate conditions in Table 2.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: What are the differences between coarse aggregates coming from processing plants and coarse…

A: Coarse aggregate are the irregular shaped broken stones or rounded natural gravel used to make…

Q: 3. A car has an initial speed of 25 m/s and a constant deceleration of 3 m/s^2. Determine the…

A: Using equations:v-u=atv2-u2=2ass=ut+12at2

Q: After placement, the temperature of the concrete was measured and recorded by thermal sensors during…

A: Datum Temperature of concrete mix = -50 C Find: Maturity of the concrete at the end of 7 days using…

Q: 1. Why do you think there is a need to agitate the aggregates inside the cylinder mold by rodding?

A: tests are done on aggregate so we can have information whether they are fit for use or not . Note…

Q: 240 mm 240 mm | P A E F B D C 160 mm 240 mm

Q: The following table shows the results obtained from Wash Test done on samples of fine aggregates.…

Q: 1. Fineness modulus of the coarse aggregate Individual Cunulative Seive (nn) Weight Retained Percent…

A: Given data-

Q: Calculate the density of the concrete Volume of the bucket = 0.00727 m3 Mass of empty bucket =…

Q: in figure. Find the elongat tensile force of 300 kN. Take Est- 14 140 300 Kn

Q: Aggregates from three sources having the properties shown in the table below where blended at a…

A: To find -The properties of aggregate blend Explanation :

Q: In an aggregate mix, the proportions of coarse aggregate, fine aggregate and mineral filler are 55%,…

Q: From a Coarse Aggregate sample, the ff data are given below to determine the sample's specific…

A: Given data, Oven dry mass A = 3625.5 g SSD mass B = 3650.3 g Mass under water C = 2293.0 g

Q: bucket and rodded with a tamping rod to determine its unit weight. The following data are obtained:…

A: V=0.3 ft3

Q: A sieve analysis test was performed on a sample of aggregate and produced the results shown in Table…

A: The table is given below,

Q: A column has a radius of 150 mm and a height of 3 meters. The density of concrete is 2.45 Mg/m^3.…

Q: 1)Determine the uncorrected and corrected weights based on the following data using the traditional…

A: Following is required mix design procedure :

Q: 5 set of sieves are to be used for analysis of aggregates. After sieve shaking the sieves, the mass…

Q: A coarse aggregate sample was dried in an oven for 1.5 hours before it was immersed in water for 24…

A: Bulk specific gravity: The ratio of the weight of the aggregate in the air of a unit volume of…

Q: The data gathered from an experiment to determine the specific gravity of aggregates were summarized…

A: Given data: Weight of FA sample w1= 171.06 gm weight of SSD sample w2= 175.38 gm weight of…

Q: 1. In the specific gravity and absorption experiment, the following measurements were taken of…

Q: WEIGHT OF RETAINED FINE AGGREGATES (g) SIEVE SIZE TRIAL 1 TRIAL 2 TRIAL 3 AVERAGE 4.75 mm 14 10 12…

A: Given Data: To Determine Fineness modulus of the Fine Aggregate Sample.

Q: CONCRETE 1 . Discuss the following: 1.1 The history of concrete . 1.2 The role of each material…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: Q3) The result of sieve analysis of a sample of aggregate given in the Table below. According to…

A: Sieve analysis: It is an analytical method that is used to determine the particle size distribution…

Q: Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit…

Q: Aggregates completely fill-up the 1 cubic meter container. If the mass of coarse aggregate inside…

A: Given:Volume of container= 1 cubic metreMass of coarse aggregate= 2010 kgSpecific gravity of coarse…

Q: Volume of measure, (ft³) Weight of measure (lb) Weight of measure + aggrega

Q: Aggregates from three sources having the properties shown in the table below where blended at a…

A: We have to determine the properties of aggregate blend for the data given in the problem. Below I…

Q: 4. Explain the usage areas and advantages of lightweight aggregates in the construction industry

A: BASIC DESCRIPTION: Light weight aggregates are way more similar to the normal ones ( Rock…

Q: The composite area shown in the figure below is composed of two rectangles. use b = 4.78 m., h = 4.6…

A: To find the radius of gyration about X-axis

Q: Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit…

A: Given that, The volume of rigid bucket= 0.2 ft3 Weight of empty bucket= 18.2 lb Weight of…

Q: Three aggregates are to be mixed together in the following ratio:Aggregate A: 35%Aggregate B:…

A: Concept used ( applied ):

Q: Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit…

A: The given data is: Volume of bucket = 1/2 ft3 Weight of Empty Bucket = 20.3 lb Weight of bucket…

Q: A sieve analysis test was performed on a sample of aggregate and produced the results shown in…

A: Following table containing Sieve no & amount retained of the soil sample is given: It is…

Q: After pouring concrete into formwork, :compaction will be required because •compaction can reduce…

A: Compaction is the process of removing air entrapped from the concrete to increase the density,…

Q: Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit…

A: According to given data Coarse aggregate is placed in a rigid bucket (mold) and rodded with a…

Q: After placement, the temperature of the concrete is measured and recorded by thermal sensors during…

A: Datum Temperature of concrete mix = -50 CTemperature vs age data for first 14 days

Q: 2. A concrete mixture given in the table below is produced. The true unit weight of concrete is…

A: Consider the above given table True unit weight of concrete is 2370 kg/m3 C} True mix proportion of…

Q: Determine the difference between the Rodded and Loose Unit Weight of aggregates

A: Difference between Rodded and Loose unit weight

Question

Quantities
Per m³ (to nearest 5 kg)
Per trial mix of
m³
Cement (kg)
370
Water (kg or litre) Fine aggregate (kg)
195
490
Coarse aggregate (kg)
10mm 20mm 40mm
1310

Item
Coarse aggregate
Sand
Table 2 Aggregates Condition
Details
Absorption capacity 1.2 %
Free moisture 2.0%
Absorption capacity 1.5%
Moisture content 3.0%

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

complete the table and answer quest
choose true or false If you know that weights of coarse aggregate as follow :Weight of aggregate stock = 5350 gm, weight of aggregate in oven dry= 5200 gm, weight of aggregate submerged in water =3254 gm, weight of aggregate SSD= 5220 gm , According to weights above , the oven dry bulk specific gravity is 2.325
The following table shows the results obtained from laboratory tests done on samples of aggregates. Weight of Aggregates + BSG for Metal Metal Measure % ABS % MC SSD Measure Inside Diameter = 6 inches Height = 12 inches Empty weight = 8.62 kg 30.39 kg 2.67 3.69 9.24 1. Calculate the Dry Rodded Unit Weight of Aggregates in kg/m³. 2. Calculate the % Voids in 1 m³ of aggregates.
From a Fine Aggregate sample, the ff data are given below to determine only the SPECIFIC GRAVITIES and ABSORPTION OF THE SAMPLE. MASS of oven dried aggregate 428.3g MASS of PYC filled with water =652.5g MASS of aggregate and water =785.3g MASS of SSD Aggregate =459.1g MASS OF AN EMPTY PYCNOMETER =125.0g MASS of oven dried aggregate 428.3g 652.5g 785.3g 459.1g 125.0g MASS of PYC filled with water MASS of aggregate and water MASS of SSD Aggregate MASS OF AN EMPTY PYCNOMETER IL || || |I
Table shows the grain size distributions of aggregates A, and B. Answer the following questions and show all calculations: What are the maximum sizes of aggregates A and B?
The modulus of elasticity of concrete (Force/Area) is 13 GN/m^2. Determine its US Customary units (kip/in^2).
Referring to the aggregate gradations A, B, and C in Figure , answer the following questions:a. What is the maximum size of each gradation?b. What is the nominal maximum size of each gradation?c. Classify each gradation as dense, open, or gap indicating the reason for each classification.
Show complete process. Aggregates from three sources having the properties shown in the table below where blended at a ratio of 30:45:25 by weight. Determine the properties of the aggregate blend.
Need answer for this please
The concrete weigh 8.5 kg. Find the specific weight of the concrete using the dimensions shown in the picture.
Question # 3: Calculate the fineness mnlulus of aggregate according to the table of the sieve analysis below. Sieve size Mass Cumulative Cumulative Percentage retained according to ASTM retained (g) percentage passing percentage retained 3/8 in 4 8. 32 16 34 30 56 50 104 100 54 <100 24
Referring to the aggregate gradations A, B, and C in Figure P5.26, answer the following questions: a. What is the maximum size of each gradation? b. What is the nominal maximum size of each gradation? c. Classify each gradation as dense, open, or gap indicating the reason for each classification. 100 A 80- 60 40 0.075 0.30 1.18 2.36 4.75 9.5 12.5 19.0 25.0 0.15 0.60 Sieve sizes (mm) FIGURE P5.26 Percent passing 20