1. Each of the four vertical links has a 8 x 36-mm uniform rectangular crosssection and each of the four pins has a 16-mm diameter.a. Determine the maximum value of the average normal stress in the linksconnecting points B and Db. Determine the maximum value of theaverage normal stress points C and E.0.4 mc. Determine the average shear stress in pinB0.25 m0.2 md. Determine the average shear stress in pinC.e. Determine the bearing stress actingbetween pin C and link CE.f. Determine the bearing stress actingbetween pin D and link BD.20 kN

solution of above problem is below:

Answered: mal stress points Ca e average shear…

Engineering

Civil Engineering

mal stress points Ca e average shear strw e average shear stre

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 75 mm x 75 mm wooden block in cross section is subjected to a load P of 300 kN. The plane A makes an angle of 14 degrees with respect to the horizontal axis (x-axis). a. Determine the normal stress at section A-A. b. Determine the shear stress at section A-A.
For the given state of stress, determine (a) the principal planes, (b) the principal stresses, (c) the orientation of the planes of maximum shear stress, (d) maximum shear stress, (e) the corresponding normal stress. 12 ksi 8 ksi 18 ksi
During the tension test, the wooden specimen is subjected to an average normal stress of 2 ksi. Determine the axial force P applied to the specimen. Also, find the average shear stress developed along the section Ɵ -a of the specimen.
3): For the figure shown below. Determine the normal and shear stresses on the plane AB. On what plane does the maximum shear stress exist. 40 kPa 20 kPa 20 kPa 80 kPa 20 kPa 420 kPv 80 KP 40 kPa
Q. 24 If the stress on two perpendicular planes through a point are 80 N/mm2 (Tensile), 30 N/mm2 (Compressive) and 50 N/mm² shear stress then the normal stress on a plane at 50° to that of tensile stress plane will be N/mm². FAQ Have any Doubt? Correct Option
Part A Determine average normal stress. (Figure 1) Express your answer with the appropriate units. Javg = Part B μA Submit Request Answer Value σ1,02= 20 MPa IVD ΑΣΦ11 Units vec ww Determine the principal stress. Enter your answers numerically separated by a comma. ? 80 MPa 30 MPa www MPa
A hydraulic punch press is used to punch a slot in a 10-mm-thick plate, as illustrated. If the plate shears at a stress of 350 MPa, determine the minimum force P required to punch the slot. Punch 745 kN 942 kN 450 kN 872 kN 677 kN Slug Plate 20 mm 75 mm Plan view of slug
In the discussion of Von-Mises criterion, how different is the description of J2 when compared to the Von-Mises stress?
What can the beam shear stress equation that was derived in Sec. 5.8 be used to calculate? hand written plz the maximum shear stress occurring at the neutral axis the shear stress at any point on the circular cross section the maximum normal stress occurring at the neutral axis none of these choices
Angle 1 Tyx Txy x-direction stress 60OMPA(compression), y-direction stress 40MPA(compression), negative shear stress 30MPA Using your assigned point determine the following for the yz-plane: Using a Mohr circle determine the stresses on the plane of the indicated angle 1. (50°). Show al calculations. Draw the orientation of the stress block for this scenario.
Question 8 of 10 View Policies Current Attempt in Progress HO D d The extruded plastic shape has dimensions of D = 37 mm, d = 35 mm, a = 99 mm, and t = 7 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 365 N. (b) If the allowable shear stress for the plastic material is 800 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion? N Answer: dik a - / 10 E ||| :
Q.1: Explain the ASD (Allowable stress Design) method.