The rectangular plate is subjected to the deformation shown by the dashed lines. Determine the- followings: 1) the average normal strain along side AB 2) the average normal strain along the diagonal AC 3) the average normal strain along the diagonal BD 4) the shear strain at B 5) the shear strain at D y

The rectangular plate is subjected to the deformation shown by the dashed lines. Determine the- followings: 1) the average normal strain along side AB 2) the average normal strain along the diagonal AC 3) the average normal strain along the diagonal BD 4) the shear strain at B 5) the shear strain at D y

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

If the state of stress on the element is 4.5 MPa in each direction, find the sigma average.
Choose the correct one and explain it
For the state of stress (in MPa) shown in the figure, the major principal stress is 10 MPa. 5- 5 The shear stress t is
For the state of stresses (in MPa) shown in the figure below, the maximum shear stress (in MPa) is 2 2
1
ox The state of stress at a given point in a material component is = 120 MPa; Oy = - 80 MPa and t = 60 MPa The loading on the component is increased so that stresses are increased to values which are k times the given values. Determine the maximum value of k if the material can withstand maximum normal and shear stresses of 300 MPa and 200 MPa respectively. 1 11
M #1 3 ksi M # 2 6 ksi 9 ksi E FOR THE ELEMENT SHOWN, DETERMINE THE MAXIMUM NORMAL STRESS AND SHOW IT ON A PROPERLY ORIENTED ELEMENT, AND DETERMINE THE MAXIMUM SHEAR STRESS AND SHOW IT ON A PROPERLY ORIENTED ELEMENT.
The state of strain at a point in a structure is measured using a 60° strain rosette as shown in Figure Q3. The material properties are E = 40 GPa and Poison Ratio = 0.35. Due to the loadings, the readings from the gauges give: Ea = 300 x 10-6 E = -250 x 10-6 E = -450 x 10-6 60 60 Figure Q3
The bronze bar 3 m long with a cross-sectional area of 350 mm2 is placed between two rigid walls. At a temperature of -20°C, there is a gap A = 2.2 mm, as shown in the figure. Find the temperature at which the compressive stress in the bar will be 30 MPa. Use a = 18.0x 10-6 / °C and E = 80 GPa. 3 m-
Q- The normal stresses on the two mutually perpendicular planes at a point are 120 MPa (Tensile) and 60 MPa (Tensile). If the shear stress across these planes is 30 MPa, find the principal stresses.
The rectangular plate is subjected to force P that causes elongation in the horizontal direction and shrinking in the vertical direction as shown with the dashed line in the figure. Assume a = 550 mm, Δx = 2 mm, and Δy = 1.1 mm. Determine the shear strain γxy at point A? Determine the shear strain γnt at point A? In micro rad What is the normal strain in the x-direction? What is the normal strain in the y-direction? What is the normal strain in the n-direction? Answer in clear way please
The aluminum bar ACDB is rigidly connected to a steel tube in CD. The data is presented in the table. If the load P is equal to 125 kN, determine: The stress of aluminum in segment AC. Answ: 63.66 MPa The stress of aluminum in segment CD. Answ: 13.93 MPa The stress in steel in segment CD. Answ: 39.79 MPa The total deformation of the bar. Answ: 0.29273 mm