On a shear plane that has an orientation of 35 degrees, the horizontal stress is 145 kPa (compression), vertical stress is 72 kPa (tension), and shear stress is 40 kPa (clockwise). What is the shear stress in kPa along the 35 degrees shear plane? 67 -135 none of the available option 250 -162 -67

Q: AW360 x 72 standard steel shape is used to support the loads shown on the beam in Figure A. The…

A: Given data,Fig is givenP=5.7KNw=15.6KN/mM=44KN.ma=1.45mFINDMaximum tensile bending stressMaximum…

Q: On a shear plane that has an orientation of 35 degrees, the horizontal stress is 145 kPa…

A: Given, orientation of shear plane =35 degrees horizontal stress=-145 kPa( as compression) vertical…

Q: parts 4-6

A: The cross section is given as

Q: A cylindrical block is 35 cm long and has a circular cross-section 10 cm in điameter. It caries a…

A: Solved below

Q: Determine the largest (allowable) compressive loadP (in kN) that can be supported by the aluminum…

A: Diameter of cyinder, D =200mmangle of plane aa with horizontal =25°Load applied =PFactor of safety,…

Q: A beam has a cross-section that is 11inches tall and 4inches wide. If the max shear in the beam is…

A: Given Load 8 kipsDepth 11 inWidth 4 inTo find out Maximum shear stress

Q: The maximum safe compressive stress in a hardened steel punch is limited to 0.8 GPa and the punch is…

A: The given data is: Maximum safe compressive stress=0.8 GPa=800 MPa The shearing stress of plate=300…

Q: At a section in a beam, the tensile stress due to bending is 50 N/mm² and there is a shear stress of…

A:

Q: d) What is the maximum in-plane shear stress and the angle of its associated plane? What are the…

A: Given, To determine, d) The maximum In-plane shear stress and the angle of its associated plane and…

Q: 1-51. During a tension test, the wooden specimen is subjected to an average normal stress of 2 ksi.…

A:

Q: Hi, I was just wondering where the "0.055" came from in the area calculation within the shear stress…

A: τ=FAyIbF=100 kN = 100 x 103 NI=2[20(200)312] +260(20)312=2.684 x 107 mm4Ay=2[90(20)(55)]=1.98 x…

Q: Problem 1 For the shown problem below with the given cross-sectional area (on the right) (1) Plot…

A: Since we can only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question…

Q: Please show intermediate steps including free body diagrams, equations used, problem setup etc. so…

A:

Q: A 42 meter solid shaft is under torsional loading 53 Nm. If in this application, the allowable shear…

A: Given: Torsional loading, T = 53N-m Allowable shear stress = 369MPa Required: Minimum diameter of…

Q: For the state of stress shown, determine two values of Øy for which the maximum shearing stress is…

A:

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.