If the allowable shear stress for each of the 0.30-in.-diameter steel pins at A, B, and C is 13 ksi, and the allowable normal stress for the 0.40-in.-diameter rod BC is 22 ksi, determine the allowable uniform loadw considering the normal stress at rod BC.4 ft

Answered: Image /qna-images/answer/47582c0a-9efa-4327-ae70-153e3ce17cc1.jpg

Answered: lowable shear stress for each of the…

Engineering

Civil Engineering

lowable shear stress for each of the 0.30-in.-diameter steel pins at A, B, and idering the normal stress at rod BC.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.1.3P

See similar textbooks

Related questions

Q: The Link AB must be made of steel with a maximum normal stress of 450 Mpa. Any stress above that…

Q: A threaded steel rod (Es = 210 GPa, dr = 12 mm, as = 12 x 10-6/°C) is held stress free between rigid…

A: Given, Es=210 GPadr=12 mm4αs=12×10-6/°Cdp=15 mτ=45 MPaσ=70MPa

Q: DETERMINE THE AVERAGE PUNCHING SHEAR STRESS THE CIRCULAR SHAFT CREATES IN THE METAL PLATE THROUGH…

Q: 2. The structure is used to support a distributed load of w = 5 kN/m. The bolts at A, B, and C each…

Q: The major and minor principal stresses at a point are 3 MPa and -3 MPa respectively. The maximum…

A: Given: The major principal stress, σ1 = 3 MPa The minor principal stress, σ2 = -3 MPa

Q: The maximum shear stress (kPa) is most nearly 100 kPa 50 kPa -50kPa 50 kPa 75 O 56 O 66 O

Q: -57. Determine the principal stress, the maximum in-plane shear stress, and ver 120 MPa MADARAKAN…

A: Given data : The value of normal stress in X direction σX=300 MPa The value of normal stress in Y…

Q: Q1. The structure shown consists of a S18 x 70 rolled-steel beam AB and two short members welded…

A: Finding out SFD and BMD of beam and maximum normal stress.

Q: pD/ the 931. For the state of stress shown in Fig. principal stresses and the maximum shearing…

A: Givenσx=80Mpa ζxy=30Mpa so the principal stress is given as σ1=+σx-σy22+ζxy2σ1=802+8022+302=90Mpa…

Q: A W18x40 standard steel shape is used to support the loads shown on the beam. Assume P= 26 kips, w =…

Q: 1.51 In the steel structure shown, a 6-mm-diameter pin is used at C and 10-mm-diameter pins are used…

Q: What is the Maximum Shear Stress, t, on the centric axially loaded member shown? The cross-sectional…

A: Given data : Axial load (P)=40 kipsCross sectional area (A)=2 in2

Q: In the steel structure shown, a 6-mm-diameter pin is used at Cand 10-mm-diameter pins are used at…

A: To find value of load P

Q: For the state of stresses (in MPa) shown in the figure below, the maximum shear stress (in MPa) is 2…

A: The maximum shear stress in Mpa is =?

Q: Problem 01.054- Analysis of an inverted T-frame In the steel structure shown, a 6-mm-diameter pin is…

Concept explainers

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.

Question

If the allowable shear stress for each of the 0.30-in.-diameter steel pins at A, B, and C is 13 ksi, and the allowable normal stress for the 0.40-in.-diameter rod BC is 22 ksi, determine the allowable uniform load
w considering the normal stress at rod BC.
4 ft

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Estimate the transverse tensile strength of the concrete in Problem 12.6.
Compute the nominal shear strength of an M107.5 of A572 Grad 65 steel.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
A beam is part of the framing system for the floor of an office building. The floor is subjected to both dead loads and live loads. The maximum moment caused by the service dead load is 45 ft-kips, and the maximum moment for the service live load is 63 ft-kips (these moments occur at the same location on the beam and can therefore be combined). a. If load and resistance factor design is used, determine the maximum factored bending moment (required moment strength). What is the controlling AISC load combination? b. What is the required nominal moment strength for a resistance factor of 0.90? c. If allowable strength design is used, determine the required moment strength. What is the controlling AISC lead combination? d. What is the required nominal moment strength for a safety factor of 1.67?
Determine the smallest value of yield stress Fy, for which a W-, M-, or S-shape from Part 1 of the Manual will become slender. To which shapes does this value apply? What conclusion can you draw from your answer?
A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The beams are spaced at 7 feet 6 inches, and the span length is 30 feet. The superimposed loads are as follows: construction load = 20 psf, partition load = 10 psf, weight of ceiling and light fixtures = 5 psf, and live load = 60 psf, A992 steel is used, and fc=4 ksi. Determine whether the flexural strength is adequate. a. Use LRFD. b. Use ASD.
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
Compute the nominal shear strength of an M1211.8 of A572 Grade 65 steel.
How does a tensile stress differ from a compressive stress?
A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The dam were plotted on a load-displacement graph. P vs. L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/L =1392 kips/in. What is the modulus of elasticity?
Use the composite beam tables and select a W-shape and stud anchors for the following conditions: Span length = 18 6 Beam spacing = 9 ft Total slab thickness = 51 2 in. (the slab and deck combination weighs 57 psf). Lightweight concrete with a unit weight of 115 pcf is used Construction load = 20 psf Partition load = 20 psf Live load = 225 psf Fy=50 ksi and fc=4 ksi A cross section of the formed steel deck is shown in Figure P9.8-9. The maximum live-load deflection cannot exceed L/360 (use a lower-bound moment of inertia). a. Use LRFD. b. User ASD.
EB and FG are two planes inside a soil element ABCD as shown in Figure 10.50. Stress conditions on the two planes are Plane EB: EB = 25 kN/m2; EB = +10 kN/m2 Plane FG: FG = 10 kN/m2; FG = 5 kN/m2 (Note: Mohrs circle sign conventions for stresses are used above) Given ; = 25, determine: a. The maximum and minimum principal stresses b. The angle between the planes EB and FG c. The external stresses on planes AB and BC that would cause the above internal stresses on planes EB and FG