Load and shape of the below knee prostheses can be modelled as two cylindrical members. Determine the maximum deformation of the prostheses, E=100MPA 800N A 25cm 50N 20cm 10cm, C 5cm 35cm D 850N (Answer: 8 2mm

Load and shape of the below knee prostheses can be modelled as two cylindrical members. Determine the maximum deformation of the prostheses, E=100MPA 800N A 25cm 50N 20cm 10cm, C 5cm 35cm D 850N (Answer: 8 2mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: d AB (G= 39 GPa). Eac

A: answer= 17.899 deg

Q: The two timber beams loaded as shown are connected by a roller support at point C and supported by…

A: Data given-

Q: Consider the truss made of 2 bars with lengths 1 m, orientated in the structure shown in Figure 1.…

Q: A rectangular aluminum block is 100 mm long in the x direction, 75 mm wide in the y direction and 50…

A: The single distributed load in the y-direction.Given:The length of the block is .The width of the…

Q: Q) Determine the reactions at the supports. E is constant. 8 kN/m B I=1250 *106 mm² 3 m 20 kN I=625…

Q: The uniform steel (E =200 GPa) bar in Fig. has a diameter of 40 mm and is subjected to the loading…

A: According to the given data E=200GPa d=40mm L=AB=BC=CD=200mm We need to find Displacement of…

Q: Determine the vertical displacement of point B. Each A-36 steel member has a cross- sectional area…

A: Given,A = 400 mm2E = 200 GPa

Q: The device is used to measure a change in temperature. Bars AB and CD are made of A-36 steel and…

Q: Delermine une angie beiween une resuilant iorce anu ne x axis. Replace the loading on the frame by a…

Q: Two members AB and AC are made of material with E= 91 Gpa and each member has cross sectional area…

A: Given: E=91 GPaP=2079 NL1=202 mm =0.202 mL2=313 mm=0.313 mL3=480 mm=0.48 m

Q: Determine the maximum shearing stress in each springs supporting the rigid bar shown. Neglect the…

A: We have a rigid bar pivoted at an end and supported by two rigid springs, with a force of 5 KN…

Q: re B 400 mm Sk ← 55 400 mm 60 kN ▾ Part A If the 20-mm-diameter rod is made of A-36 steel and the…

A: To find: The deflection in the rod. Given: The diameter of the rod is d=20 mm. The stiffness of the…

Q: If an isotropic material has a shear modulus of 11 Gpa and a Poisson's ratio of 0.34, calculate its…

Q: The frame shown in Fig. 2 consists of a rigid member CBD and a flexible cable AB. If 80 KN is…

A: P=80kN To find displacement at point D

Q: Question Three: Derive expressions that shows 1) Relationship between modulus of elasticity and…

Q: The prismatic bar has a circular cross section with 100-mm diameter. In a test to determine its…

Q: The assembly consists of three titanium (Ti-6A1-4V) rods and a rigid bar AC. Agr=2 in² 1 ft F-2A- P…

A: GivenApplied force Length of rod AB and CD cross-section area of rod AB and CD is Length of rod EF…

Q: Let's consider a rod having a solid circular cross-section with diameter of 6 mm and it is made of a…

Q: As an airplane's brakes are applied, the nose wheel exerts two forces on the end of the landing gear…

A: According to the given dataWe need to find the reaction at point C and Force of AB

Q: BD rod made of G1 = 78 GPa with a diameter of 27 mm attached to the CA tube at point B, the tube…

A: We are suppose to solve only 3 subparts. Please post other parts as a separate question.

Q: *3-32. The block is made of titanium Ti-6A1-4V and is subjected to a shortening of 0.06 in. along…

Q: A bar of varying square sections is loaded as shown in the figure. Determine the total elongation.…

Q: A 1D two-node bar element as shown below is considered. The displacement of node 1 is q₁=0.002 mm,…

A: q1 = 0.002 mm qp = 0.013 mm let take, X1 = 10 mm Xp = 15 mm X2 = 35 mm To find out:- Displacement…

Q: A) Determine the elongation of the square hollow bar when it is subjected to the axial force P = 120…

A: To find: A) Elongation of the square hollow bar when it is subjected to the axial force P = 120…

Q: Two 2 by 4 cm 1062 steel bars are butt-spliced with two 3 by 4 cm 1016 splice plates using six M14…

A: We have to find the correct formula for finding shear stress

Q: torsion as shown. Determine the Perimeter of then

A: we know that , shear stress =T2t Am A0 =T2tζ Am = A0T = Torque t = thickness to obtain area we…

Q: QUESTION 13 The compound steel bar shown in Figure is made of three uniform segments marked as 1, 2…

Q: Determine the horizontal displacement of end point D of the steel rod shown in the figure. E=200 GPa…

Q: -Determine the elongation of the steel bar 1m long and 1.5 cm cross-sectional area when subjected to…

A: Given data: A = 1.5 cm2 Pulling force = 1500 kg Length of the steel bar (L) = 1 m…

Q: Rigid bars AB and BCD are supported by pins A and D and by a steel rod at C. There is a roller E =…

Q: A rectangular aluminum block is 100 mm long in the x direction, 75 mm wide in the y direction and 50…

Q: The rigid lever arm is supported by two A-36 steel wires having the same diameter of 4 mm. Determine…

A: Draw free body diagram of lever arm Taking net moment about E

Q: Four 10 kg masses are being supported by an 800mm solid rod. The rod is being supported at both…

Q: A steel compression member of 9-ft effective length supports an eccentric load as shown. Using the…

Q: The column is loaded with an axial force of P = 2,050 kN through a rigid endplate. Determine the…

Q: Problem 4. The structure in the figure is composed of two rigid bars (AB and CD) and two vertical…

A: The free-body diagram of the beam is as shown below, Assumption: Let the length of aluminum and…

Q: If the steel rod shown is acted upon as shown, Compute for the total deformation of the rod. Assume…

Q: Determine the total elongation of the figure shown. Use E1 = 70 GPa, and E2 = 100 GPa 0.5 m D₁ =…

A: To find: The total elongation of the figure. Given: The young's modulus of bar 1 is E1=70 GPa. The…

Q: The member has a cross section with the dimensions shown, and is subject to an internal moment Mof…

Q: A steel shaft with a length of 3.00 m. One meter of the steel is contained in a brass tube and…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

1- Load and shape of the below knee prostheses can be modelled as two cylindrical members.
Determine the maximum deformation of the prostheses, E=100MPA
800N
25cm
50N
20cm
10cm
C
5cm
35cm
850N
(Answer: 8 2mm
A,

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The two rods (A-B and B-C) shown in the left panel are connected by pins at A, B, and C. The cross sections of A-B and B-C are 10mm×13mm and 10mm×10mm, respectively. The bilinear stress-strain relation shown in the right panel is for the material used to make the two rods, where Ei is the slope of the stress-strain curve for stresses between 0 and 80 MPa and E2 is the slope for stresses larger than 80 MPa. Note that Hooke's law is only valid for stresses up to 80 MPa. A 1 1 B 0.900 m 3 P = 30 kN 2.44 m C σ MPa 80 E₂ = 40 GPa E₁ = 80 GPa E a) Given the conditions above, find the axial elongation for each rod when subjected to P=30KN. b) Find the final position of Point B due to the applied load P at that location. Hint: Assume point B moves by unknown amounts Ax and Ay from its initial position, and then use right triangles to write the known final lengths of the cables in terms of Ax and Ay. The equations can be simplified by assuming terms Ax² and Ay² are so small they can be…
If the steel rod shown is acted upon as shown below, compute for the total deformation of the rod. Assume E = 200GPa and A = 25mm2..
2. Two steel cables support an applied load of 100 kN as shown in the figure below. Determine the following: a. The deformation of member AC and member BC. b. The vertical and horizontal displacement of point C. A A = 75 sq. mm L = 3 m E = 200 GPa 22° C 45° 18° A = 75 sq. mm В L = 3 m 100 kN E = 200 GPa %3D
For the following structures, determine the maximum normal stress,deformation and displacement of point D relative to point A.
The channel shape cross-section and the rectangular cross-section shown in the Figure Q4 are made of materials with elastic-perfectly plastic behaviour. The yield stress of the material used for the channel shape cross-section is oy = 473 MPa, whereas that used for the rectangular cross- section is 0.850y. Compute the thickness of the web, t, of the channel shape section if the two cross sections have identical plastic bending moment about the z-axis. In Figure 4, h= 77 mm, b=46 mm, a=11 mm, H=77 mm, d= 46 mm N b h a + N a | d H
2.) Calculate the torsion constant for the following open and closed sections, which all have a thickness of 5mm. a = 100mm, b = 150mm, R=150mm. Which has the highest torsional rigidity if made of the same material? b a b a a a R
Part A The lever is attached to the shaft A using a key that has a width d and length of 26 mm .If the shaft is fixed and a vertical force of 200 N is applied perpendicular to the handle, determine the dimension d if the allowable shear stress for the key is T = 37 MPa (Figure 1) Express your answer with the appropriate units. HA d = Value mm Submit Request Answer Provide Feedback Next > Figure d -20 mm 500 mm 200 N
Please answer for I have 30 minutes left. Thank you.
แสดงวิธีทำให้หน่อยครับ
1. Rod ABCD is made from two materials with two cross sectional areas. The rod is subjected to axial loads as shown. Neglect the weight of the rod and determine the displacement of point A. EBE Ep =210 Gla 125 kN EAg = 70 GR ABE Aco=900 u AAB = 450 mm 37stEN/ %3D 2m 2.5m
Statics of Rigid Bodies (Round off to two (2) decimal places. Include negative sign (-) if the answer is negative.) The 13 kips force F acting on the simply supported beam. Determine the y component of F?
Consider the pre-deformation cross-section of a bar, a side view of which is shown in the figure below. h ΫΠ' ΑΣΦ D The diameter of the bar is d = 230 mm. A bending moment is applied that causes the neutral axis to become concave up. What is the normal strain h = 40 mm from the bottom of the bar if the radius of curvature is measured to be p = 6.7 m? Express your answer to three significant figures. ► View Available Hint(s) Ax ↓↑ vec t O ? mm/mm