The member has a cross section with the dimensions shown, and is subject to an internal moment Mof 43 kN-m. Calculate the resulting compressive stress o o in MPa. Express your response using three significant digits. 40 mm - 20 mm M 200 mm 20 mm 80 mm 80 mm

Q: The shear strain is calculated using the torque and the polar moment of inertia.

A: In the given statement it is asked wheather shear strain is calculated using torque and polar moment…

Q: The composite shaft, consisting of aluminum, copper, and steel sections, is subjected to the loading…

A: Given data:- To find:- the displacement of B with respect to C the normal stress in each section

Q: The copper pipe [G = 7,000 ksi] has an outside diameter of 3.875 in. and a wall thickness of 0.250…

A:

Q: The drill shown is jammed in the wall and is subjected to the torque and force shown in the diagram.…

A: Given

Q: Determine stress produced by tensile force of 20 N applied on cross sectional area of 5 mm2

A: Given data: Tensile force (F) = 20 N Cross sectional area (A) = 5 mm2 Need to determine the stress…

Q: The horizontal bar ABC is supported by a pin at A and the two rods with identical lengths and…

A: Using similar triangle approach Here, the length and area of both of the rods are the same.

Q: (e) E = бу 30 MPa Txy 85 MPa Ox 120 MPa = =

A: GivenPart eσx=-120MPaσy=30MPaτxy=85Mpa part fσx=30MPaσy=-80MPaτxy=15Mpa

Q: Determine the stress at the middle of rod BC in MPa for a given truss structure. If the diameter of…

A:

Q: A carbon steel ball with 27-mm diameter is pressed together with an aluminum ba Determine the…

A: Carbon Diameter, dc = 27 mmAluminium Diameter, dA = 35 mmForce, F =11 NPoissons Ratio, 0.3…

Q: Draw and stress tensonr with the following characteristics The stress cube visualization at point…

A:

Q: The solid circular rod has a cross-sectional area of 470 mm². It is subjected to a uniform axial…

A:

Q: Find the Vertical Support Reaction at G (in kN). Input the magnitude only (don't include a negative…

A:

Q: The bell crank is in equilibrium for the forces acting in rods (1) and (2). The bell crank is…

A: The given information in the problem is shown in the following attached image:

Q: A column has a square cross-section that increases by depth from 0.5 m to 1 m. If the column has a…

A: W are to derive the normal stress on section aa

Q: A hollow steel tube with an inside diameter of 100 mm must carry a tensile load of 400 kN. Determine…

A: Given data, Di = 100 mm. Tensile load = P = 400 KN = 400000 N. Stress= σ = 120 MN/ m2 = 120 N/mm2…

Q: d2 mm 60 mm FAN dlmm 10 mm 40 mm The shaft shown is subjected to the axial force(F) of 30 kN. If the…

A:

Q: Problem No. 3. The compound shaft has the following properties: G in both Segment 1 Segment 1 pipe…

A:

Q: The distribution of stress in an isotropic aluminium machine component is given (in MPa) as: σ₂ = y…

A:

Q: Two loads P act as shown, one parallel to (x0) and another parallel to z0; each load P equals 2.0…

A:

Q: A pipe has an outer radius of 2in and an inner radius of 1.7 in, it is subjected to the forces…

A: GivenP=150 lbT=20 lb ft=20×12=240 lb inro=2in     ie. do=4inri=1.7in    ie. di=3.4in

Q: A 5-kN tensile load is applied to a test coupon made from 1.6-mm flat steel plate (E = 200 GPa, v =…

A:

Q: Determine the cross-sectional area of the shaft. Answer: A = 1 mm²

A: Given that :Vertical shaft diameter, d=20 mmthickness of plate,  t=21 mmCollar thicknesses,…

Q: is it okay to solve this even if it is not in equilibrium? Why?

A: Solution:

Q: A compression load of P = 55 kips is applied to a 2 in. by 2 in. square post, as shown. Determine…

A: Given:-P=55 kipsl=2 inb=2 inα=30°To find:-Stress perpendicular to plane AB,  σN

Q: A compression load of P = 55 kips is applied to a 2 in. by 2 in. square post, as shown. Determine…

A:

Q: Determine the force required to produce stress of 2 N/mm2 if cross sectional area is 2 mm2

A: Given data : Cross sectional area=A Stress=σ   Required : Force

Q: |F 2F a 3F| b a

A:

Q: In the image below, B and C are pulleys. The belts on the pulleys exert the forces shown in the…

A:

Q: The inner diameter of this shaft is 80 mm and the outer diameter is 100 mm. The applied loads are…

A: Given:To find:Maximum allowable load P.

Q: sectional area of Arod = 0.75 in². If a load of P = 24 kip is applied to the end of rod, determine…

A:

Q: Given the section is subjected to a moment of 500 N-m, calculate the normal stress in MPa at the…

A:

Q: Determine the maximum value of the force P (kN) that can be applied to member AD if the allowable…

A: Given data: - The force applied at point A is P. The force applied at point B is FB = 12 kN. The…

Q: For the connection shown, determine the average shear stress in the 0.75-in.-diameter bolts if the…

A: Given data: P=64 kips diameter of bolt (d)= 0.75 in.

Q: Find normal stress . Take d=1.1 mm

A: Given data : Tensile load=P Diameter of circular rod=d   To find : Normal stress

Q: at some point sha has à diameter a isider the croSs section of a solid and its material has a yield…

A: Given, Tension = T Vertical shear force = V

Q: A force of F = 13 kips is applied as shown in the figure below. If the diameter of the bolt is d =…

A: Given data:- force (F) = 13 kips  the diameter of the bolt (d)= 1.4 inches, To find:-the maximum…

Q: A moment about the z-axis of 192 N-m is applied to a beam with dimensions b = 85 mm and h = 302 mm.…

A: Given: The beam with a rectangular section 85mm x 302mm or 0.085m x 0.302m. The beam is subjected to…

Q: The copper pipe [G = 7,000 ksi] has an outside diameter of 3.000 in. and a wall thickness of 0.125…

A: For solution refer below images.

Q: A horizontal load P of magnitude 100 kN is applied to the beam shown. Determine the largest distance…

A: Given data: Magnitude of load applied = 100 kN                    Maximum allowable tensile stress =…

Q: The wide-flange beam is subjected to the 50-kN force. Determine the principal stresses in the beam…

A:

Q: 04 It is required to find the dimensions of thick cylinder which has internal diameter of (150+SN)…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.