Answered: L wl? 8 M Figure \ Figuur la b d

Engineering

Civil Engineering

L wl? 8 M Figure \ Figuur la b d

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Design the beam using IPE shape.
The horizontal member shown in the figure is loaded by 57 kN at E. It is supported by steel connector AB (E = 200 GPa, A= 615 mm² ) and aluminum connector CD (E = 70 GPa, A = 525 mm² ). Determine the deformation incurred by connectors AB and CD. Also, calculate the vertical displacement of E. 57 kN 0.5 m 0.3 m E B 0.25 m 0.5 m
A square post with a tubular cross section is loaded as shown in the figure below. a) Determine the state of the stress at point A having sides parallel to x and y axes. b) Determine the principal planes and principal stresses at point A at the base of the post.
Steel structure design
QUESTION 3) A horizontal beam AD is supported by an inclined strut CB and carries a load of 15 kN at joint D in the figure. The strut, which consist of two bars each of thickness 40 mm, is connected to the beam by a rivet passing through the three bars meeting at joint C. The allowable shear stress and bearing stress are t-60 MPa and o=120 MPa, respectively. a) Determine the required diameter of the rivet at the hinge C that carry safely by the given system. b) If the diameter rivet used on the support A is 20 mm check whether this rivet diameter is sufficient for the given system. 0.8m Im 0.6m 15 kN В Beam AD 20mm Strut CB 40mm 100mm 40mm 50mm 100mm Detail of joint C Detail of joint A
Rhelp**
Check the cross-section for bending if the allowable normal stress is o =±120 MPa. a: + + 1 = 4 m a = 15 cm q = 3 kN/m a +
2. The beam with cross-section shown carries a uniformly distributed load of intensity w over its entire length. Determine w if the allowable stresses are g = 40 MPa, g = 80 MPa, and t = | T 12 MPa. w (kN/m) 75 mm 10 mm 0.5 m : 10 mm 3m 10 mm- 150 mm 150 mm
A simply-supported beam with length, L = 10 m, is carrying a downward uniform load, w = 31 kN/m throughout its length. The cross-section of the beam is shown in the figure with a = 480 mm, b = 24 mm, c = 24 mm, and d = 177 mm. Determine the maximum flexural shear stress in MPa. 19 a tot a fof d *
Q1. A horizontal bar of nagligible weight and assumed rigid is supportad by two rads, AB and CD, and hingad : the right and. Data for the rods are as follows: Rod AB: L= 2 m, A= 1950 mm. E= 80 GPa ; Rod CD: L=2.5 m, A= 1200 mm, E= 200 GPa Ifthe maximum unit stress in AB is not to exceed 90 MPa, and the maximum allowabla load for CDis 110 kN, determine the maximum value of the force F. B F 0.60 m. 1.90 m 1.20 m
Completely solve and draw the free-body diagrams. Box the final answers. Note: AB is 3 m long, BC is 2 m long, and CD is 4 m long.
P1.4 Three solid bars, each with square cross sections, make up the axial assembly shown in Figure P1.4/5. Two loads of P = 30 kN are applied to the assembly at flange B, two loads of Q = 18 kN are applied at C, and one load of R = 42 kN is applied at end D. The bar dimensions are b₁ = 60 mm, b₂ = 20 mm, and b3 = 40 mm. Determine the normal stress in each bar. (1) b₁ B P (2) FIGURE P1.4/5 (3) Q D R