It proposed to provide pile foundation for a heavy column; the pile group consisting of 4 piles,placed at 2.0 m centre to centre, forming a square pattern. The under-ground soil is clay, havingCu at surface as 60 kN/m², and at depth 10 m, as 100 kN/m². Compute the allowable columnload on the pile cap with factor of safety of 3.0, if the piles are circular having diameters 0.5 meach and length as 10 m.

Answered: It proposed to provide pile foundation…

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter12: Pile Foundations

Section: Chapter Questions

Problem 12.12P

See similar textbooks

Similar questions

A pile group of 25 piles has to be proportioned in a uniform pattern in soft clay with equal spacing in all directions. Assuming the value of cu to be constant throughout the depth of the piles, determine the optimum value of spacing of piles in the group. Assume a = 0.7. Neglect point bearing effect, and assume the piles to be circular.
A 400 mm 400 mm square precast concrete pile of 15 m length is driven into a sand where = 18.0 kN/m3 and = 33. Assuming = 0.7 and K = 1.4Ko, determine the load carrying capacity of the pile with factor of safety of 3.0.
Figure P12.36 shows a 3 5 pile group consisting of 15 concrete piles of 400 mm diameter and 12 m in length. What would be the maximum load that can be allowed on the mat with a factor of safety of 3? The piles have a center-to-center spacing of 1200 mm.
Consider a 500 mm diameter pile having a length of 18 m in a clay. Given: γ = 20.0 kN/m3 and cu = 60 kN/m2. Determine the maximum allowable load (Qall) with FS = 3. Use the α method and Table 12.11 for determining the skin friction and Eq. (12.20) for determining the point load. Allow a factor of safety of 3. What percentage of the ultimate load is being carried by the pile shaft? Is it a friction pile?
Redo Problem 18.10 using the method for estimating the skin resistance. 18.10 A concrete pile 15 m long with a cross section of 380 mm 380 mm is fully embedded in a saturated clay layer. For the clay, sat = 18 kN/m3, = 0, and cu = 80 kN/m2. Assume that the water table lies below the tip of the pile. Determine the allowable load that the pile can carry (FS = 3). Use the a method to estimate the skin resistance.
A 600 mm diameter and 25 m long driven concrete pile carries a column load of 1200 kN. It is estimated that the shaft carries 900 kN and the point carries 300 kN. Determine the settlement of the pile head using the Poulos and Davis method with the following data: Es = 25 MN/m2, Ep = 30,000 MN/m2, and s = 0.2
In a piled raft, 450 mm diameter and 13 m long piles are placed in a rectangular grid at 1.60 m 1.63 m spacing. Find the pile-raft interaction factor assuming uniform soil conditions with depth and
Redo Problem 12.3 using Coyle and Castellos methods for estimating both Qp and Qs. 12.3 A 500 mm diameter and 20 m long concrete pile is driven into a sand where = 18.5 kN/m3 and = 32. Assuming = 0.7 and K = 1.5 Ko, determine the load-carrying capacity of the pile, with a factor of safety of 3. Use Meyerhofs method [Eq. (12.18)] for computing the point load-carrying capacity Qp, and Eqs. (12.42) and (12.43) for computing the load-carrying capacity of the pile shaft Qs.
Refer to the pile shown in Figure P9.1. Estimate the side resistance Qs by Using Eqs. (9.40) through (9.42). Use K = 1.5 and Coyle and Castello’s method [Eq. (9.44)]
Determine the maximum load that can be allowed on a 500 mm diameter and 18 m long pile driven into a clay where = 20.0 kN/m3 and cu = 60 kN/m2. Use the a method for determining the skin friction. Allow a factor of safety of 3. What percentage of the ultimate load is being carried by the pile shaft?
Redo Problem 12.20 using Vesics method, assuming that the skin friction is distributed uniformly along the shaft. 12.20 A 600 mm diameter and 25 m long driven concrete pile carries a column load of 1200 kN. It is estimated that the shaft carries 900 kN and the point carries 300 kN. Determine the settlement of the pile head using the Poulos and Davis method with the following data: Es = 25 MN/m2, Ep = 30,000 MN/m2, and s = 0.2
Solve Problem 12.23 using the method of Broms. Assume that the pile is flexible and free headed. Let the soil unit weight, = 16 kN/m3; the soil friction angle, = 30; and the yield stress of the pile material. FY = 21 MN/m2. 12.23 A 30 m long concrete pile is 305 mm 305 mm in cross section and is fully embedded in a sand dcposit. If nh = 9200 kN/m2, the moment at ground level Mg = 0, the allowable displacement of pile head = 12 mm; Ep = 21 106 kN/m2, and FY(pile) = 21,000 kN/m2, calculate the allowable lateral load, Qg, at the ground level. Use the elastic solution method.

SEE MORE QUESTIONS

Recommended textbooks for you

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Geotechnical Engineering (MindTap…

Civil Engineering

ISBN:

9781305635180

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781305081550

Author:

Braja M. Das

Publisher:

Cengage Learning

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Geotechnical Engineering (MindTap…

Civil Engineering

ISBN:

9781305635180

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781305081550

Author:

Braja M. Das

Publisher:

Cengage Learning

Construction Materials, Methods and Techniques (M…

Civil Engineering

ISBN:

9781305086272

Author:

William P. Spence, Eva Kultermann

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS