A uniform symmetrical beam is supported at two pin joints as shown below. It has a length L and a uniformly distributed load pz (x) = pis applied. The maximum bending moment My (x) will be half way along the beam. L р If the length L is 6.2 m, and the distributed load p is 2,400 N/m, then calculate the value of My (x) at the mid-point. Enter your answer as an integer, in Nm but without the units.

A uniform symmetrical beam is supported at two pin joints as shown below. It has a length L and a uniformly distributed load pz (x) = pis applied. The maximum bending moment My (x) will be half way along the beam. L р If the length L is 6.2 m, and the distributed load p is 2,400 N/m, then calculate the value of My (x) at the mid-point. Enter your answer as an integer, in Nm but without the units.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Don't solve if you are not confident... Try to answer it correctly
Problem 2 Consider the beam of length L and cross-sectional moment of inertia I shown in the figure below. q(x) = qox/L x = 0 a) Find the equation for the deflection of the beam. b) Find an expression for the internal bending moment. c) If the beam has a square cross-section with side length h, find an expression for the maximum bending stress at x = 0. x = L
PLEASE SHOW COMPLETE AND STEP BY STEP SOLUTION
The horizontal beam is supported by a pin at A and the pin-connected link BC. It has a uniformly distributed loading w = 7.0 kN/m as shown in the figure. All the pins are in double shear and have a diameter of 20 mm. Determine the max shear stress in the pin at A. Input your answer as a value only in MPa to one decimal place without +/- sign. W 1.5 m 2 m B 1 m
The cross-sectional dimensions of a beam are shown. Assume b-2.5 in., t-tw-0.25 in. and d=4.25 in. (a) If the bending stress at point K is 2560 psi (T), determine the internal bending moment M₂ acting about the z centroidal axis of the beam. (b) Determine the bending stress o H K Answers: (a) M₂ = (b) σH = bf i i tw at point H (positive if tension, negative if compression). lb-ft. psi.
Figure Q2 shows a statically determinate plane truss subjected to a horizontal concentrated load at B. The truss is made using steel with Young's modulus of 205 GPa, and the cross section area for all members are constant. If the horizontal displacement at B is limited to 10 mm, determine the minimum cross section area required for the truss. The solution can be based on Method of Conservation Energy or Method of Virtual Work. (а) (b) Based on Q2(a), suggest an appropriate steel bar measurement.
A triangular distributed load of max intensity w = 320 N/m acts on beam AB. The beam is supported by a pin at A and member CD, which is connected by pins at C and D respectively. Determine the reaction forces at A and C. Enter your answers in Cartesian components. Assume the masses of both beam AB and member C'D are negligible. BY NC SA 2016 Eric Davishahl A D В C X Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value a 5.90 m 9.44 m 4.13 m The reaction at A is A N. %3D The reaction at C is C = ĵN. +
Figure Q2(a) shows a cantilever beam that is subjected to a pure bending moment M = 3kN.m about the neutral axis (N.A) and the cross-section of a beam is shown in Figure Q2(b). Determine: (a) The moment of inertia about the neutral axis, InA. (b) The bending stress acting at point B and state whether it is in tension or compression. (c) The bending stress acting at point C (d) The maximum bending stress in the beam. M Figure Q2 (a) 20 mm B 150 mm C N 20 mm 150 mm 20 mm 250 mm Figure Q2 (b)
Please answer precisely thankyou
tate of Stress Caused by Combined Loadings Learning Goal: To use the superposition principle to find the state of stress on a beam under multiple loadings. The beam shown below is subjected to a horizontal force P via the rope wound around the pulley. The state of stress at point A is to be determined. 100 mm 15 mm 20 mm 200 mm 150 mm f 20 mm The dimensions are di - 2.15 m. d₂ = 0.5 m. -0.85 m d-285 mm and r= 150 mm The applied force has magnitude P=4.5 kN Part A-Support Reactions and Internal Loading C₁, C₂=₁ N=, V = ₁ M = Determine the support reactions C, and C, and the internal normal force, shear force, and moment on the cross-section containing point A. Express your answers, separated by commas, to three significant figures. ► View Available Hint(s) Submit Part B- Properties of the Cross-Section A= I= Q = Submit VAX IT VOC JA=.TA= What are the cross-sectional area, moment of inertia with respect to the neutral axis, and first moment of the area with respect to point A for the…
Pls answer a to c. thanks
strength of materials