Interaction diagram of a rectangular reinforced concrete beam- column is shown in fig. with reference to this figure, which of the following statements in (i) and in (ii) below are correct? Pu fek bd R, M (i) (a) Point Q represents balanced failure (b) Point R represents balanced failure (c) Point P represents balanced failure (d) Point Q represents balanced failure under maximum eccentric compression (ii) (a) PQ corresponds to the primary tension failure range (b) QR corresponds to the primary tension failure range (c) QR corresponds to the primary compression failure (d) PQ corresponds to the range of increase in axial force capacity with increase in bending moment capacity.

Interaction diagram of a rectangular reinforced concrete beam- column is shown in fig. with reference to this figure, which of the following statements in (i) and in (ii) below are correct? Pu fek bd R, M (i) (a) Point Q represents balanced failure (b) Point R represents balanced failure (c) Point P represents balanced failure (d) Point Q represents balanced failure under maximum eccentric compression (ii) (a) PQ corresponds to the primary tension failure range (b) QR corresponds to the primary tension failure range (c) QR corresponds to the primary compression failure (d) PQ corresponds to the range of increase in axial force capacity with increase in bending moment capacity.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. The column in the figure shown has a strain on its compressive edge equal to -0.003 and has a tensile strain of +0.00185 on its other edge. Detemine the nominal values of Pn and Mn that cause this strain distribution if f'c = 21 MPa, fy = 414 MPa. Draw the column interaction diagram. en 600 Pn mm 8 - 6 32mm 75 225 225 75 600
A small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 125 mm. The cross-sectional dimensions of the tee shape are b = 15 mm, d = 23 mm, and t = 9 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 με is measured from a strain gage located at c = 9 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P?
Problem II. An exhaust gas piping fabricated as shown is subjected to a bending moment, an internal pressure, and a torque. In points A and B, the following stresses occur due to the loading: o 63.5 MPa, B=127 MPa, = 127 MPa A.B A.B a. Determine Gmin, omax, and its direction (in degrees) from x-axis at point A. b. Determine omin, omax, and its direction (in degrees) from x-axis at point B. 1 B d O A x
A small aluminum alloy [E = 80 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 165 mm. The cross- sectional dimensions of the tee shape are b = 19 mm, d = 29 mm, and t = 7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 430 µɛ is measured from a strain gage located at c = 10 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P ЗР Strain gage d D E H Answer: P = i
A square beam (w=0.03 m) is loaded with a point load of 1000 N and a moment load of 1000 Nm, as shown. i. Determine maximum deflection of the beam using step by step analytical equations. ii. Determine the Maximum stress in the beam using step by step analytical equations iii. For both top fibers and bottom fibers of the square beam, specify the type of the stresses.
A small aluminum alloy [E= 77 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 160 mm. The cross- sectional dimensions of the tee shape are b= 22 mm, d = 33 mm, and t= 4 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 410 uɛ is measured from a strain gage located at c = 10 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? %3D %3D %3D 3P Strain gage E Answer:
Q1: The beam shown in Figure 1 is subjected to a vertical force Pv and a horizontal force Ph. The data for Pv, Ph, a,L,and e are shown in Table 1. Determine the maximum compressive and tensile stresses under the vertical force (at a distance a from the left support.) Pv = 80k N a = G0o 6 omm e %3D 26 K N 120 mm L =3600 mm Figure 1 250 mm
A simple pin-connected truss is loaded and supported as shown. The load Pis 240 kN. All members of the truss are aluminum pipes that have an outside diameter of 130 mm and a wall thickness of 14 mm. Determine the normal stress in each truss member. Assume truss dimensions of a = 10 m, b = 6.25 m, and c= 5 m. Tensile stress is positive, while compressive stress is negative. b D Answer: OAB 11 JAC OBC= OBD = OCD = i M M a B MPa MPa MPa MPa MPa
6. In Fig. 6, a 1.5 m long cantilever beam with a circular cross section (R = 100 mm) and two symmetrically positioned longitudinal holes is loaded by a concentrated force P at its tip. The material is a titanium alloy with a 600 MPa maximum allowed working stress when bent. Find the maximum permitted vertical force P value. 1.5 m Radius= R = 100 mm Radius of hole =
2. (3 points) When loading is applied at a point on a body, the stress distributions at different cross sections are different. However, the stress distribution becomes uniform at locations far from the applied load. This is due to which principle? Name the principle. P Load distorts lines located near load P P C C Lines located away from the load and support remain straight P O avg A section a-a section b-b section c-c -Load distorts lines located near support Your answer
A thin polymer plate PQR is deformed so that corner Q is displaced downward 0.9 mm to new position Q', as shown in. Determine the shear strain at Q' associated with the two edges (PQ and QR). Assume a = 150 mm, b = 216 mm, c = 180 mm, and A = 0.9 mm. a b P R C Answer: Shear strain y = Q i A X urad.
Problem 8.57 The sign is subjected to the uniform wind loading. Determine the stress components at points A and B on the 100-mm- diameter supporting post. (Eigure 1) Figure 7 of 8 > Review Determine the normal stress at point A. Express your answer using three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. HÅ ? JA= Value Units Submit Request Answer Determine the shear stress at point A. Express your answer using three significant figures and include the appropriate units. μA C ? Value Units Review Part C Determine the normal stress at point B. Express your answer using three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. μA Ⓒ ? TB - Value Units Submit Request Answer Determine the shear stress at point B. Express your answer using three significant figures and include the appropriate units.…