Q) The rectangular plate shown in the figure below with dimensions h=20 mm and b=50 mm changes shape symmetrically with respect to the x-axis after in-plane loading. At the same time, point B is displaced in the plane Ab 0.12 mm, Ah 0.03 mm. After deformation; a) What is the strain in the x-axis direction? b) Find &cb c) What is the angle of shear between the DG and GH edges?

Q) The rectangular plate shown in the figure below with dimensions h=20 mm and b=50 mm changes shape symmetrically with respect to the x-axis after in-plane loading. At the same time, point B is displaced in the plane Ab 0.12 mm, Ah 0.03 mm. After deformation; a) What is the strain in the x-axis direction? b) Find &cb c) What is the angle of shear between the DG and GH edges?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 125 mm. The cross-sectional dimensions of the tee shape are b = 15 mm, d = 23 mm, and t = 9 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 με is measured from a strain gage located at c = 9 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P?
Question 1: The piece of plastic is originally rectangular. Given LCD and LAD are 400 and 300 mm, respectively. If the plastic distorts as shown by the dashed lines, a) Determine the average normal strain that occurs along CD. b) Determine the average normal strain that occurs along AD. c) Determine the shear strain Yxy at corner C. 2 mm LCD 2 mm D LAD mm B 12 mm 3 mm mm
Problem 2 For the beam shown in the figure A) Draw the shear-force and bending-moment diagrams for the beam shown in the figure. B) For the composite section, aluminium [E = 70 GPa] bonded to a steel [E = 210 GPa], located at the maximum bending moment, determine: (1) the maximum bending stresses in the aluminium and steel bars. (2) the stress in the two materials at the joint where they are bonded together. K4N/M 2m B 10kN/mm 4m 2m D Steel Aluminum 42mm 20 mm 13 mm
Given: E= 29x10^6 psi A= 2in^2 Determine the deformations members AB, BC, BE, DE and DF. Please show your complete handwritten solution.
A small aluminum alloy [E = 80 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 165 mm. The cross- sectional dimensions of the tee shape are b = 19 mm, d = 29 mm, and t = 7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 430 µɛ is measured from a strain gage located at c = 10 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P ЗР Strain gage d D E H Answer: P = i
A small aluminum alloy [E= 77 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 160 mm. The cross- sectional dimensions of the tee shape are b= 22 mm, d = 33 mm, and t= 4 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 410 uɛ is measured from a strain gage located at c = 10 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? %3D %3D %3D 3P Strain gage E Answer:
Thanks for the help
to the direction of loading. When When solving for Normal/Axial/Compressive/Tensile Stress we look at an area of our member that is solving for basic Shear Stress we look at an area to the direction of loading. This is because of how the members will fail in either situation and what resists that failure. Parallel, Parallel 1000 Parallel, Perpendicular Perpendicular, Parallel Perpendicular, Perpendicular
A mild steel bar of square cross-section 40 mm x 40 mm is 400 mm long it is subjected to a longitudinal tensile stress of 440 N/mm² and lateral compressive stress is 200 N/mm² in perpendicular directions. E = 2 x 105 N/mm², μ = 0.3. What is the approximate elongation of the bar in the longitudinal direction?
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 6) What is the deformation &c in mm? 0.8m 0.4m B 5KN 0.6m 20KN A=800 mm? A=1,200 mm²
1.4
The tensile member shown, 60mm x 80mm in cross-section is subjected to a load of 250kN. The plane AA’ makes an angle of 15o with the x-axis. What is the tensile stress of section AA’? Determine the shear stress on plane AA’ At what angle of plane AA’ is the shear maximum.