(c) In an Air Handling Unit (AHU) below shown in Figure 2, the fan inS.A. is driven by a variable speed drive (VSD) with 5- 25mA. That isinresponse to the temperature sensor input in between 16.5°C and25.5°C.E.A.R.A.RTF.A.S.A.(TV-LOPFigure 2Find,(i) input span;(ii) output span;(iii) the proportional gain;(iv) bias;(iii) the general form of transfer function; and(iv) the temperature sensor input when the driving current is15mA.RETURN VATERSUPPLY VATER

As per the honor code I will attempt only first three parts. Please repost the other questions.…

indling Unit (AHU) below shown in Figure 2, the fan in S.A. is driven by a variable speed drive (VSD) with 5- 25mA. That is in response to the temperature sensor input in between 16.5°C and 25.5°C. E.A. R.A. FA. S.A. TV-D LOP Figure 2 Find, (i) input span; (ii) output span; (iii) the proportional gain; RETURN VATER SUPPLY VATER

indling Unit (AHU) below shown in Figure 2, the fan in S.A. is driven by a variable speed drive (VSD) with 5- 25mA. That is in response to the temperature sensor input in between 16.5°C and 25.5°C. E.A. R.A. FA. S.A. TV-D LOP Figure 2 Find, (i) input span; (ii) output span; (iii) the proportional gain; RETURN VATER SUPPLY VATER

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

3. A factory's separately excited DC generator has an armature resistance of 0.252. The machine is driven at 1000 revolutions per minute giving the following data: E,[V] I[A] a) Plot the open circuit characteristic when the machine is driven at 1000 and at 1500 rev/min. b) If the machine is drive at 1500 rev/min and its field current is adjusted to 0.2 A, plot the output voltage (in the same axis with (a)) as the load current is varied from 0 to 40A. For a full load current of 40A, what is the voltage regulation? 5 28 75 112 132 150 0.1 0.3 0.5 0.7 0.9
Q5- Adjust a fire angle for a three-phase full-wave semi-controlled converter to feed the separately exciter DC motor to get a load torque can be reached to 750 rpm. When the supply voltage of converter is 150 volts per-phase and the absorbed current through the armature 40A with resistance 0.2 2 and a constant back emf 0.4v/rpm. Then find the maximum speed for motor assume the previous parameters values are a constant.
7. The following table relates to the open-circuit curve of a shunt gen- erator running at 750 rev/min: Generated voltage (V) Field current (A) 172 300 360 385 395 10 1 3 4 5 Determine the no-load terminal voltage if the field circuit resistance is 125 N. If the speed is now halved, what is the resultant terminal voltage? At the reduced speed, what value of field circuit resistance will give a no-load terminal voltage of 175 V? (N.C.T.E.C., O.2)
A sepesately excited de molor is supplied by buck conreater ( cheppes). a
I want to represent each point on the graph paper with its corresponding scale written alongside it.
I need help on this asap:
The parameters of a three-phase, 50 Hz, 6-pole, 400 V star connected induction motor are r1 = 0.3 ohm, x1 = 0.5 ohm, r’2 = 0.15 ohm and x’2 = 0.2 ohm. The voltage and frequency of the induction motor is controlled by a power electronic converter (inverter). Calculate the required inverter output frequency and voltage to drive the induction motor load at 0.2 the rated speed of the motor and calculate the current drawn by the motor for that case. The formula for the maximum slip is given below:
A brushed DC motor is spinning at a maximum no-load speed of 6206 rpm. The nominal brush voltage drop is 0.67 V and the rated terminal voltage of the machine is 13 V. Determine the voltage constant, Ke, of the machine in Vs/rad.
f) Write the mathematic expresion for the Series Injected Voltage in UPFC for the following control cases: a) Voltage Regulation: b) Impeadance Compensation: c) Phase Shifter:
Please solve last time rejected. For ac voltage controller type with an input of 230 V, 50 Hz is connected to a resistive load of 20 ohms. The circuit is operating with the switch ON for 30 cycles and OFF for30 cycles Determine1)r.m.s output current and2) input power factor.
7. The following table relates to the open-circuit curve of a shunt gen- erator running at 750 rev/min: Generated voltage (V) Field current (A) 10 172 300 360 385 395 0 1 2 3 4 Determine the no-load terminal voltage if the field circuit resistance is 125 N. If the speed is now halved, what is the resultant terminal voltage? At the reduced speed, what value of field circuit resistance will give a no-load terminal voltage of 175 V? (N.C.T.E.C., O.2)
An armature controlled DC motor has the following parameters: Tf = 0.03 Nm KT = 0.15 Nm/A Imax = 2.4 A KĘ = 0.15 Vs/rad Wmax = 5000 rpm R = 0.8 Ohms 1. Determine the following: (i) The maximum output torque. (ii) The maximum power output. (iii) The maximum armature voltage. (iv) The no load motor speed when e = Emax 2. Plot the following relationships: (i) Torque versus current (ii) Induced voltage versus speed 3. If the above motor is operated at 3000 rpm with a load torque of 0.15 N.m, determine the armature voltage