A separately excited DC motor rated at 200 V, 900 rpm, 160 A, has an armature resistance of 0.065 , fed from single phase fully controlled rectifier with an ac voltage source of 240 V, 50 Hz. Assuming continuous conduction, calculate the firing for rated motor torque and 900 rpm.

A separately excited DC motor rated at 200 V, 900 rpm, 160 A, has an armature resistance of 0.065 , fed from single phase fully controlled rectifier with an ac voltage source of 240 V, 50 Hz. Assuming continuous conduction, calculate the firing for rated motor torque and 900 rpm.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The current drawn by the a 230 V DC motor of armature resistance 0.5 Ω and back emf 200 V is ?
I hope the solution is written in clear handwriting
A 240 V, 50Hz single phase supply feeds a SP-FC-FWR. The rectifier is used to power the armature of a separately excited DC motor. The DC motor ratings are 220 V, 10 A (armature current), 940 rpm, Ra= 1.750. What is the no-load speed of the motor?
Q2/A synchronous motor having 60 % reactance and a negligible resistance is to be operated at rated load (i) u.p.f. (ii)0.6 p.f. lag (iii) 0.6 p.f. lead .What are the values of e.m.f. ? Indicate assumptions made ,if any.
Solve it fast fast plz
Q9) Specifications for a PM DC motor are as follows: • electrical constant (KEMF) = 0.014V/rpm • and armature resistance=202. What are the motor's no-load speed (w), stall torque, and maximum power for an applied voltage of 12 V? ((rad/s-0.105 rpm)) V ww000 RA IA LA Veur TM 18.0 JM T₂
Q5- Adjust a fire angle for a three-phase full-wave semi-controlled converter to feed the separately exciter DC motor to get a load torque can be reached to 750 rpm. When the supply voltage of converter is 150 volts per-phase and the absorbed current through the armature 40A with resistance 0.2 a and a constant back emf 0.4v/rpm. Then find the maximum speed for motor assume the previous parameters values are a constant.
"A 220 V, compensated shunt motor driving a 1084.8 N.m torque load is running at 1000rpm. The efficiency of the motor at this load is 92 percent. The combined armature, compensating winding and interpole resistance is 0.01 ohm, and the resistance of the shunt field is 65 ohm. Determine the following parameters of the motor: (i) Input power (in kW) (ii) Field current (in Amp) (iii) Armature current (in Amp) (iv) Induced voltage in armature (in volts) (v) Torque developed by motor (in N.m) and (vi) The resistance of a dynamic breaking resistor (in ohm) that will be capable of developing 678 N.m of braking torque at a speed of 750 rpm. Assume windage and friction at 750 rpm is the same as at 1000 rpm. [Hint: 1 lb-ft = 1.356 N.m]" T T T Arial v 3 (12pt) - T-
600V, DC series motor operates at 600 rpm and rated load. Armature resistance 0.1 ohm and series fieldwinding resistance is 0.05 ohms. At full load, the motor draws 195 A current. A) Find the reverse(back) EMF value at full load. B) Find the power and internal moment produced in the armature under full load.
A 250 V shunt motor, having an armature resistance of 0.2 ohm draws fromthe mains a current of 50 A on half full load. The speed is to beincreased to twice half full load speed. If the torque of the motor is ofconstant magnitude, determine the percentage change in flux required.[Ans. 52.29] I WANT A DIFFRENT APPROACH (NOT COPY PASTE ON LIBRARY)
A 1200 rpm, 700V Series DC motor has an armature resistance of 20 and the field resistance of 90. If the rotational losses is 450W and the efficiency is 71% , the output power of the motor in Kwatt is
power electronics and drives