Indirect extrusion reduces a cylindrical billet with dimensions of 3.93 inches in length and 2 inches in diameter to 0.78 inches. Die angle is 90 degrees. According to the Johnson equation, the calculated ram pressure is 2578 MPa with a = 0.8 and b = 1.4. Calculate: a) Determine true strain b) Extrusion ratio c) Extrusion strain d) Ram force (MN) Please submit the final answers in 2 decimal places

Indirect extrusion reduces a cylindrical billet with dimensions of 3.93 inches in length and 2 inches in diameter to 0.78 inches. Die angle is 90 degrees. According to the Johnson equation, the calculated ram pressure is 2578 MPa with a = 0.8 and b = 1.4. Calculate: a) Determine true strain b) Extrusion ratio c) Extrusion strain d) Ram force (MN) Please submit the final answers in 2 decimal places

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3G Z 4.5G+ l. Which of the following stress or .10 strength parameters is used in the computation of the force in an extrusion (operation (one best answer a) average flow stress O ,b) compression strength) O ,c) final flow stress) O d) tensile strength) O ?e) yield strength O
Please answer all parts
4.) A sheet-metal part is 2.0 mm thick and 20.0 mm wide. It is bent to an angle 60° and a bend radius 10 mm in a V-die. The metal has a yield strength Sy= 220MPA, Young's modulus of E=200GPA, and a tensile strength SUTS=340 MPa. a.) Determine the bend radius after springback, Rf mm b.) Determine the bend angle after springback, af c.) Compute the required force to bend the part, given that the die opening dimension w=25 mm. (use k=1.3 for V die). F= kN
Question 4 The channel shape cross-section and the rectangular cross-section shown in the Figure Q4 are made of materials with elastic-perfectly plastic behaviour. The yield stress of the material used for the channel shape cross-section is Oy=441 MPa, whereas that used for the rectangular cross-section is 0.70y. Compute the thickness of the web, t, of the channel shape section if the two cross sections have identical plastic bending moment about the z-axis. In Figure 4, h= 83 mm, b=48 mm, a=12 mm, H-83 mm, d= 48 mm Z H b h Z d H
0.075L T 0.8 4.0 -7.0 + All dimensions in inches -2.0- 0.1 T 0.205 0.25 T 0.25 5) Rolling: A rolling operation is performed on a 5 mm thick sheet of low carbon steel (K=530, n=0.26 from Table 8.1). The sheet is reduced by 0.2 mm each pass. The friction at the dies is 0.3. The roller diameters are 50 mm. The sheet width is 125 mm. a) Find the roll force for the 3rd pass. For the 3rd pass the initial thickness is 4.6 mm and the final thickness is 4.4 mm. a) Estimate the power to perform the 3rd pass if the roll rotates at 100 rpm.
Round number to three significant figures. 1.548937 x 10^7
6) 32. Initial volume of the billet is same final volume in forging process. Select one: True False
Q2. (30 Marks) For the following figure: 1. Read the tolerances (GD&T) from the figure? 2. Write the Opitz code (5 digits only) for this product? 3. Write few points about point cloud? And how it can be used to inspect the geometry of products? 4. Draw sketch (free hand) to the top view of the figure below? (()) 5. For the symbol below the figure, what does it means? () will jo الهندسي 08±0.01 A 020±0.01 00.02MAM BM 010±0.01 00.02MAM ماذا يعني هذا B
The casting shown is to be made in cast iron using a wood pattem. Perform the calculations required to determine the dimensions of the patten. Machining allowance, 3 mm / side, Shrinkage allowance for length/external 1 mm / 100 mm Shrinkage allowance for cored-hole 0.8 mm / 100 mm, Draft allowance external Imm / 100mm Draft allowance internal 2 mm / 100mm • 80 6 80 80 80 500 300 300 Final shape after all allowances are applied. 300 x 500 side at the top is on the parting plane. (All dimensions are in mm). You have to show calculations and dimensions at each stage.
i) ii) iii) iv) с 1.000 1.000 What is the MMC? What is the LMC? Ø.515-.540 Hole +0.010@ABC 1.000 Figure 1 What is the geometric tolerance value? What datum(s) control(s) perpendicularity? B Ø.495-.500 Pin +0.005@ABC A Hole Pin
Question 4 a) Each cylinder in a four-cylinder car engine has a bore diameter of 63.53 mm and the stroke for each piston is 175.00 mm. Calculate the cubic capacity of the engine in cm3 and calculate the clearance volume per cylinder for a compression ratio, r, of 6.25. b) The bore diameter of each cylinder in a six-cylinder four-stroke internal combustion engine is 32 mm and the stroke of each piston is 125 mm. During testing, the engine runs at 1450 revolutions per minute (rpm) with a pressure-volume indicator diagram showing a mean net area of 2.90 cm² and a diagram length of 0.85 cm. The pressure scale on the indicator diagram is set to 165 kN/m² per cm. Calculate the mean effective pressure (m.e.p) and the indicated power in kilowatts (kW) developed by this six-cylinder four-stroke engine. Give your answer to 2 decimal places. c) A hollow connecting rod has an inner diameter of 26.25 mm and is subjected to an axial tensile load of 500 MN. If the maximum allowable stress for this…
a.) determine average normal strain along AC after load has been applied. b.) determine average shear strain at A relative to x and y axis (gamma xy =) c.) determine average shear strain at point C relative to the x and y axes after deformation (gamma xy)