In the shaft shown in the figure, the gears are attached to the A992 steel shaft (G = 75 GPa). find the angle of twist of end B with respect to end A knowing that the shaft diameter is 40 mm. Consider L1 = 470 mm, L2 = 640 mm and L3 = 740 mm. 400 N-m 1200 N-m B 600 N-m 200 N m TL J = 32 JG' %3D もり、 %3D

In the shaft shown in the figure, the gears are attached to the A992 steel shaft (G = 75 GPa). find the angle of twist of end B with respect to end A knowing that the shaft diameter is 40 mm. Consider L1 = 470 mm, L2 = 640 mm and L3 = 740 mm. 400 N-m 1200 N-m B 600 N-m 200 N m TL J = 32 JG' %3D もり、 %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A solid stainless steel [G = 108 GPa] shaft that is 1.2 m long will be subjected to a pure torque of T = 82 N-m. Determine the minimum diameter d required if the shear stress must not exceed 40 MPa and the angle of twist must not exceed 4.7°. Report both the maximum shear stress 7 and the angle of twist at this minimum diameter. Answers: d = mm. T = IN i MPa. i
Gear shaft ABCDE is subjected to the torques shown in the figure. Find the internal torque in each seg- ment, and then plot the torsional moment diagram. Assume that the spacing between gears is constant, i.e., 10 in. T1 = T2 = 1000 lb-in. 500 lb-in. A B T3 = 800 Ib-in. C Ta = 500 lb-in. d = 1.0 in. D T; = 800 lb-in. E
600 Nm An aluminum shaft with a constant diameter of 50 mm is loaded by torques applied to gears attached to it as shown in Figure. Using G = 28 GPa, determine the relative angle of twist of gear D relative to 900 Nm 1100 Nm 2 m 800 N-m gear A. 3m 2 m
The solid steel shaft is supported by the frictionless customer on D and E. This system The mile provided 5 kW of power in w dev / second and was connected to a motor at C. wwww ww www ww ww www wwwm www w A and B If gears get primary 2 kW and 3 kW, determine the minimum shaft diameter. w rotation speed and The safety shear stress is known and is included in the table below. pictures. wwww ww wwwwwwwww www wwwwww wwwwwwww wwwwwwwww w(cycle/second) = 100 tem(Mpa) = 40 3 kW 5 kW 2 kW A D B E C _
Shafts ab and ce are support by pillow bearing blocks as shown. Compute the angle of twist at point a. Report your answer in degrees to two decimal places. 35 in A Y bearing bearing gear c: radius 2.0 in 2 in-k gear b: shaft ab: shaft ce: radius 5.0 in b a radius 0.5 in 5 in-k radius = 0.7 in d. bearing e bearing all shafts: G = 12000 ksi 25 in 30 in
A straight gear with module m = 5 mm and face width bw = 40 mm has center distance cd = 0.1875m. The pinion has 25 teeth, the speed is 1000 rpm, and pressure angle ᶲ = 200. Find the Hertzian contact stress at the pitch point when the gear transmits 10 kW. Neglect friction forces. The gear steel has modulus of elasticity E = 207 GPa and a Poisson’s ratio of 0.30.
with diameter d = 38 mm transmits 37 kW to a gear Calculate the required speed of rotation (number of at B. The allowable shear stress in the steel is 40 MPa. X7-3 A motor driving a solid circular steel shaft revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit. Motor d = 38 mm B
The four gears shown are attached to a steel shaft that is rotating at 2 Hz. Gear B supplies 70 kW of power to the shaft. Of that power, 20kW are used by gear A, 20 kW by gear C and 30kW by gear D. -20KW 7OKN -20kw -30kW 2m 1.5m 1.5m B (a) If a uniform shaft diameter of 125 mm B speci fied, detenmine the angle of rotation of A relative to D. O If segment Co is to be replaced ay a hollaw Shaft with an inside diameter of 80 mm, what is the outside diameter if the stress is not to excced 70 MPa.
500 N.m 1500 N.m B 800 N.m 600 mm A 500 mm 300 N.m 400 mm
A compound shaft drives three gears, as shown. Segments (1) and (2) of the compound shaft are hollow bronze [G= 6,500 ksi] tubes, which have an outside diameter of 2.15 in. and a wall thickness of 0.2100 in. Segments (3) and (4) are solid 1.00-in.-diameter steel [G= 11,500 ksi] shafts. The shaft lengths are L₁ = 78 in., L₂ = 12 in., L3 = 20 in., and L4 = 26 in. The torques applied to the shafts have magnitudes of TB = 990 lb-ft, Tp = 450 lb-ft, and TE = 160 lb-ft, acting in the directions shown. The bearings shown allow the shaft to turn freely. Using the sign convention presented in Section 6.6., calculate: (a) the magnitude of the maximum shear stress in the compound shaft. (b) the rotation angle of flange C with respect to flange A. (c) the rotation angle of gear E with respect to flange A. TB TD (1) TE (3) Answer: (a) Tmax (b) DC/A = (C) ΦΕΙΑ = LI (2) B psi rad rad C L3 D (4) LA E -X