In a broaching machine shown, shaft A carries a pulley 60.96 cm in diameter which is driven by a leather flat belt from 12-inch pulley on the 30 Hp-squirrel-cage, compensator-motor shaft overhead, the latter turning 1200 rpm. Gears 2 & 4 have 12 teeth each, and 3 & 5 have 60 teeth each. Gear 5 is fast to 6, which has 10 teeth and a module of 8.465 mm/tooth and which engages with rack 7 to which is attached the broach. Assuming that there is no slipping between the pulleys and the belt. Determine: a) the speed with which the broach is drawn through the work, in m/s. b) Specify a double ply, medium weight, cemented joint leather flat belt, considering a mildly jerking loads and a center distance of 60 inches. c) Determine the belt tensions of the belt and the F, maximum stress in the straight part of ALBA belt if¹ = 3 F₁ F₂ Gear 6 Gear 5 Rack CEO CEC A Gear 2 030-0--30 Gear 4 Gear 3

Q: In the gear system shown, the motor applies a 190 lb-ft torque to the gear at A. A torque of Tc=392…

A:

Q: Determine the minimum shaft diameter at locations A, B, C, D, & E for an enclosed industrial…

A:

Q: Calculate the angle of twist at point A. A for the following diagrammed problem. There is a 1600…

A: The diameter of shaft AB is .The diameter of shaft CD is .The diameter of gear B is .The diameter of…

Q: A pair of spur gears with 20° tooth form transmits 1.0-hp. The pinion is mounted on the shaft of an…

A:

Q: A helical gear of 10 inches pitch diameter has a helix angle of 25 degree, and there are 35 teeth.…

A: Detailed explanation and solution of the above problem uploaded in below picture.

Q: 1. The shaft rotating at 200 rpm carries a spur gear C having 80 teeth with a diametral pitch of 8.…

A:

Q: The lathe machine in the Central University of Technology mechanical workshop uses epicyclic gear…

A:

Q: In the double-reduction gear train shown (dimensions are in inches), shaft a is driven by a motor…

A: Step 1: Step 2: Step 3:

Q: below. Determine: (1) the torque in shaft c-d to the nearest in-lb and (2) the angle of twist at…

A: To determine the torque in the shaft and the angle of twist at a pointgivenradius of gear b=radius…

Q: Referring to the given figure, spur gear A receives 5 hp at 650 rpm thl B is an idler and gear C is…

A:

Q: Shaft a in the figure has a power input of 75 51T kW at a speed of 1000 rev/min in the…

A: Given data Input power = 75 kW Input Speed = 1000 rpm module = 5 mm Number of teeth on gear 1 = z1 =…

Q: 2-2 The sun gear-2 and -5 are integral with the input shaft of the compound epicyclic gear…

A: givensun gear 2 and 5 are integral part with the input shaft of the compound epicyclic gearannular…

Q: Determine the minimum shaft diameter at locations A, B, C, D, & E for an enclosed industrial…

A: The power transmitted by gear B, P1 = 25 hpThe number of teeth on gear B, Z1 = 24The diametral pitch…

Q: In a gear set, a 36-tooth spur pinion drives a 60-tooth spur gear. The teeth of these gear are cast…

A: We can answer up to 3 sub-parts so we will answer first 3. Please resubmit the question by…

Q: Problem 5-49: The splined ends and gears attached to the A992 steel shaft are subjected to the…

A: The diameter of the shaft, (d)=40 mmFor A992 steel we take the value of shear modulus, (G)=75…

Q: A similar pair of helical gears , also on parallel axes, are to have involute teeth, of 20o normal…

A: Given data: CD=146 mmϕn=20°Z1=26Z2=34 Need to determine  the transverse pressure angle in degrees.

Q: An epicyclic gear train, as shown in Fig. 1, has a sun wheel S of 30 teeth and two planet wheels P-P…

A:

Q: A and d The teeth are of

A:

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.