In the network shown in Fig.2 the voltage source is given by vs = 24 cos (100t) V and the current source is given by is = 12 cos (200t) A. Find the effective value (RMS) of V. Do not use T-equivalent. The impedances value are given for the frequency of the voltage source. Figure 2 US 392 ww 40mH ell 100mH 392 ww + 50mH 10mF

In the network shown in Fig.2 the voltage source is given by vs = 24 cos (100t) V and the current source is given by is = 12 cos (200t) A. Find the effective value (RMS) of V. Do not use T-equivalent. The impedances value are given for the frequency of the voltage source. Figure 2 US 392 ww 40mH ell 100mH 392 ww + 50mH 10mF

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.22P: The real power delivered by a source to two impedances, Z1=4+j5 and Z2=10 connected in parallel, is...

See similar textbooks

Similar questions

Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
The real power delivered by a source to two impedances, Z1=4+j5 and Z2=10 connected in parallel, is 1000 W. Determine (a) the real power absorbed by each of the impedances and (b) the source current.
Please help with the solution.
Please help with d,e, and f.
Please help with the solution.
Example: For the circuit shown, if the applied non-sinusoidal e=150sin1000t+ 100sin2000t+75sin3000t V. Find the active value of the current passes e(+ through the circuit and the average consumed power in the circuit? R-50 L-5mH voltage is: 50uF
The maximum transferred average power to a load without restrictions calculated in terms of the RMS (effective) value of Vth is: Select one: O a. IVthl/Rth O b. Vthl2/4.Rth OC. IVl²/8.Rth O d. IVl²/2.Rh
Please answer alll subparts for like either dislike...
The peak amplitude of the sinusoidal voltage source in the circuit shown in the figure is 180 V, a phase of 0 degrees, and its frequency is 5000 rad/s. a)Find VTH and ZTH for the thevenin equivalent circuit. b)Draw the thevenin circuit. c)Calculate the average power delivered to the load (between points a and b) when the load consists of a resistor and capacitor with RL=2000 0 and CL=0.2 uF. d)Determine the settings of RL and CL that will result in the most average power being transferred. e)What is the average power in (c)? Is it greater than the power in (a)? 6 kN 0.6 H a Vg 12 k2 9. +
An industrial installation has a power factor of 0.85 in backward. The demand is 150 KVA, and the operating voltage is 4800 V at 60 Hz. What should be done to bring the power factor to 0.95 in lagging? Indicate what you would connect and with what three-phase power. If the connection of the element to be added is in delta, indicate its reactance and the value of its capacitance or inductance. capacitance or inductance.
two devices are connected across a source where F= 60 Hz. If the 2 rms values of the voltage drops across the devices are 115V and 90V which are out of phase by 90°. Find the equation across the source and sketch the equivalent circuit diagram.
can you doing this with detail explaination..thank you!