In the given figure, a cantilever beam has annular cross-section. The ratio of the inner diameter of the section to the outer diameter is d, ld, = 0.6 and the shear modulus of the material is G= 80GPA. If the allowable shear stress is t=100 MPa, and the maximum allowable twist angle is 2=1.8°. 20kNm 19 kNm 11kNm D a) Calculate the cross section dimensions d, and d, values. B 2m 4m 3m b) Draw the stress distribution on the most critical cross section according to the dimensioning. d. kiriş enkesiti

In the given figure, a cantilever beam has annular cross-section. The ratio of the inner diameter of the section to the outer diameter is d, ld, = 0.6 and the shear modulus of the material is G= 80GPA. If the allowable shear stress is t=100 MPa, and the maximum allowable twist angle is 2=1.8°. 20kNm 19 kNm 11kNm D a) Calculate the cross section dimensions d, and d, values. B 2m 4m 3m b) Draw the stress distribution on the most critical cross section according to the dimensioning. d. kiriş enkesiti

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rectangular plate is deformed into the shape shown by the dashed lines. Suppose that a = 260 mm and b = 450 mm (Figure 1) 2 mm a mm D B 6 mm 6 mm 2 mm -3 mm -x 1.) Determine the average normal strain along diagonal BD. 2.) Determine the average shear strain Yzy at corner B relative to the x, y axes..
The cross-sectional dimensions of the beam shown in the figure are a = 4.9 in., b = 6.8 in., d = 4.5 in., and t = 0.30 in. The internal bending moment about the z centroidal axis is M2 = -3.65 kip-ft. Determine (a) the maximum tension bending stress (a positive number) in the beam. (b) the maximum compression bending stress (a negative number) in the beam. b y (ур.) d a Answers: (a) Omax T psi (b) Omax C= psi
The state of stress at a point is shown on the element. Enter your answers numerically separated by commas. ΥΠ ΑΣφ vec max min = ksi Submit Request Answer Figure Part B Determine the absolute maximum shear stress. ΑΣφ ve 2.5 ksi ksi Fabs mar= 4 ksi Submit Request Answer 5 ksi Provide Feedback 圓
The cross-sectional dimensions of the beam shown in the figure are a = 4.0 in., b = 4.7 in., d = 4.1 in., and t = 0.30 in. The internal bending moment about the z centroidal axis is Mz = -3.90 kip-ft. Determine (a) the maximum tension bending stress (a positive number) in the beam. (b) the maximum compression bending stress (a negative number) in the beam.
Current Attempt in Progress A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the left by u = 1.7 mm and upward by v = 4.3 mm to new position Q'. Determine the shear strain y at corner Q' after deformation. Use c = 670 mm, a = 20°, and B = 70°. R Answer: Y = i prad
Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If 0 = 68 MPa, determine the principal stresses acting at the point. 114 MPa 66 MPa 157.9 MPa and -155.4 MPa 82.0 MPa and -83.7 MPa O 121.2 MPa and -138.0 MPa O 167.4 MPa and -98.1 MPa O 133.2 MPa and -131.2 MPa
The steel tube seen below has an outer diameter do = 60mm and an inner diameter d, = 50mm. It is subjected simultaneously to torque T = 1.5kN-m and to axial load P = 205kN. Determine: (a) the maximum in-plane shear stress and its orientation, (b) the associated normal stress and (c) sketch both on a properly oriented element.
The cross-sectional dimensions of the beam shown in the figure are a = 4.1 in., b= 5.1 in., d= 4.3 in., andt= 0.33in. The internal bending mornent about thez centroidal axis is M, = -4.15 kip-ft. Determine (a) the maximum tension bending stress (a positive number) in the beam. (b) the maximum compression bending stress (a negative number) in the beam. b y |(ур.) |d a Answers: (a) OmaxT psi (b) Omax C= psi
The curved bar shown has a cross section of 30 x 30 mm. Knowing that the allowable compressive stress is 175 MPa, determine the largest allowable distance a. Take P= 4.5 kN. В. A. P P 30 mm 20 mm 20 mm 30 mm The largest allowable distance a is mm.
30 mm C A B 150 mm M 150 mm 300 mm 30 mm - determine the bending stress developed at points A, B, and C. Sketch the bending stress distribution on the cross section. - Assume that the cross-section has a moment of inertia about the neutral axis of 1.907 x 10-4 m². - Assume that the neutral axis is located 97.5 mm from the bottom of the cross-section - Assume the internal bending moment M = 61.4 kN.m
Due to loading, the plate is deformed into the dashed shape shown in the figure. Assume a = 39 in., b= 33 in., δ1= 0.1625 in., δ2= 0.1 in. Determine the average normal strain along the side AB?in micro rad And answer in right and clear way Determine the average shear strain in the plate at A relative to the horizontal and vertical axes?
A horizontal load Pof magnitude 96 kN is applied to the beam shown. Determine the largest distance a for which the maximum tensile stress in the beam does not exceed 75 MPa. 20 mm 20 mm P. 20 mm 60 mm 20 mm The largest distance a is mm.