In the figure, a 16 kg block is held in place via a pulley system. The person's upper arm is vertical; the forearm makes angle 0 = 32° with the horizontal. Forearm and hand together have a mass of 1.8 kg, with a center of mass at distance d₁ = 14 cm from the contact point of the forearm bone and the upper-arm bone (humerus). The triceps muscle pulls vertically upward on the forearm at distance d₂ = 2.0 cm behind that contact point. Distance d3 is 37 cm. Take the upward direction to be positive. What are the forces on the forearm from (a) the triceps muscle and (b) the humerus? (a) Number (b) Number i Triceps- com Humerus di Units Units < <> Block

In the figure, a 16 kg block is held in place via a pulley system. The person's upper arm is vertical; the forearm makes angle 0 = 32° with the horizontal. Forearm and hand together have a mass of 1.8 kg, with a center of mass at distance d₁ = 14 cm from the contact point of the forearm bone and the upper-arm bone (humerus). The triceps muscle pulls vertically upward on the forearm at distance d₂ = 2.0 cm behind that contact point. Distance d3 is 37 cm. Take the upward direction to be positive. What are the forces on the forearm from (a) the triceps muscle and (b) the humerus? (a) Number (b) Number i Triceps- com Humerus di Units Units < <> Block

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter12: Static Equilibrium And Elasticity

Section: Chapter Questions

Problem 37P: To get up on the roof, a person (mass 70.0 kg) places 6.00-m aluminum ladder (mass 10.0 kg) against...

See similar textbooks

Similar questions

To get up on the roof, a person (mass 70.0 kg) places 6.00-m aluminum ladder (mass 10.0 kg) against the house on a concrete pad with the base of ladder 2.00 m from the house. The ladder rests against a plastic rain gutter, which we can assume to frictionless. The center of ladder is 2.00 m from the bottom. The person is standing 3.00 m from the bottom. Find the normal reaction and friction forces on the ladder at its base.
When tightening a bolt, you push perpendicularly on a wrench with a force of 165N at a distance of 0.140m from the center of the bolt. How much torque are you exerting relative to the center of the bolt?
Find the net torque on the wheel in Figure P10.23 about the axle through O, taking a = 10.0 cm and b = 25.0 cm. Figure P10.23
A crane of mass m1 = 3 000 kg supports a load of mass m2 = 10 000 kg as shown in Figure P10.36. The crane is pivoted with a frictionless pin at A and rests against a smooth support at B. Find the reaction forces at (a) point A and (b) point B. Figure P10.36
To get up on the roof, a person (mass 70.0 kg) places a 6.00-m aluminum ladder (mass 10.0 kg) against the house on a concrete pad with the base of the ladder 2.00 m from the house. The ladder rests against a plastic rain gutter, which we can assume to be frictionless. The center of mass of the ladder is 2 m from the bottom. The person is standing 3 m from the bottom. What are the magnitudes of the forces on the ladder at the top and bottom?
Consider the disk in Problem 71. The disks outer rim hasradius R = 4.20 m, and F1 = 10.5 N. Find the magnitude ofeach torque exerted around the center of the disk. FIGURE P12.71 Problems 71-75
What three factors affect the torque created by a force relative to a specific pivot point?
A wooden door 2.1 m high and 0.90 m wide is hung by two hinges 1.8 m apart. The lower hinge is 15 cm above the bottom of the door. The center of mass of the door is at its geometric center, and the weight of the door is 260 N, which is supported equally by both hinges. Find the horizontal force exerted by each hinge on the door.
Consider the downhill race in Example 13.9 (page 372). The acceleration of a particle down an incline is aparticle = g sin ,where is the angle the incline makes with the horizontal.Show that the acceleration of a rolling object down an incline isgiven by aCM=aparticale1+f
A stepladder of negligible weight is constructed as shown in Figure P10.73, with AC = BC = = 4.00 m. A painter of mass m = 70.0 kg stands on the ladder d = 3.00 m from the bottom. Assuming the floor is frictionless, find (a) the tension in the horizontal bar DE connecting the two halves of the ladder, (b) the normal forces at A and B, and (c) the components of the reaction force at the single hinge C that the left half of the ladder exerts on the right half. Suggestion: Treat the ladder as a single object, but also treat each half of the ladder separately.
A uniform beam resting on two pivots has a length L = 6.00 m and mass M = 90.0 kg. The pivot under the left end exerts a normal force n1 on the beam, and the second pivot located a distance = 4.00 m from the left end exerts a normal force n2. A woman of mass m = 55.0 kg steps onto the left end of the beam and begins walking to the right as in Figure P10.28. The goal is to find the womans position when the beam begins to tip. (a) What is the appropriate analysis model for the beam before it begins to tip? (b) Sketch a force diagram for the beam, labeling the gravitational and normal forces acting on the beam and placing the woman a distance x to the right of the first pivot, which is the origin. (c) Where is the woman when the normal force n1 is the greatest? (d) What is n1 when the beam is about to tip? (e) Use Equation 10.27 to find the value of n2 when the beam is about to tip. (f) Using the result of part (d) and Equation 10.28, with torques computed around the second pivot, find the womans position x when the beam is about to tip. (g) Check the answer to part (e) by computing torques around the first pivot point. Figure P10.28
A thin rod of length 2.65 m and mass 13.7 kg is rotated at anangular speed of 3.89 rad/s around an axis perpendicular to therod and through one of its ends. Find the magnitude of the rodsangular momentum.