In order to determine the polarization resistance of a carbon steel in acidic solution, a potential isapplied and the current measured. We obtain the following valuesE - Eco (mv)-15-10-5-20251015i (mA cm-2)-8.5-6.0-2.6-1.001.12.85.09.0The anodic and cathodic Tafel coeffic.nts are equal to: ßa = 30 mV, Bc = 50 mV.Calculate (a) the polarization resistance at the corrosion potential and (b) the corrosion currentdensity.

In order to determine the polarization resistance of a carbon steel in acidic solution, a potential is applied and the current measured. We obtain the following values E - Econx (mv) -15 i (mA cm-2) -8.5

In order to determine the polarization resistance of a carbon steel in acidic solution, a potential is applied and the current measured. We obtain the following values E - Econx (mv) -15 i (mA cm-2) -8.5

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The assembly consists of a brass shell (1) fully bonded to a solid ceramic core (2). The brass shell [E = 115 GPa, a = 18.7 × 10-6/°C] has dout 50mm. and din = 35mm. The ceramic core [E = 290 GPa, α = 3.1 x 10-6/°C] has a diameter dout = 35mm. At a temperature of 15°C, the assembly is unstressed. AT = 60°C. Find the internal stress in the brass. = 200 mm Brass shell (1) (2) Ceramic core
Which of the following statements is incorrect about ceramics? A Ceramics have very weak interatomic bonding. (B) Ceramics have a low coefficient of thermal expansion © Ceramics can be crystalline or nanocrystalline (amorphous). (D Ceramics can be used as a matrix material in composites.
Transformers are considered as an electrical power transmission source Select one: O True O False
Which of the following alloys would form a complete substitutional solid solution? Metal 1 is BCC, metal 2 is FCC, and atomic radíus difference is 12%. Metal 1 is FCC, metal 2 is FCC, and atomic radius difference is 12%. Metal 1 is FCC, metal 2 is FCC, and atomic radíus difference is 15%. Metal 1 is HCP, metal 2 is FCC, and atomic radius differene is less than 15%. Metal 1 is BCC, metal 2 is BCC, and atomic radius difference is at least 15%.
A rigid bar, AB, is pinned at point B. Two other bars, AC and AD, are connected to point A to provide support for AB. We are investigating the behavior of this system under a specific load. Key Details: Bar properties: Material: Steel with Young's modulus (Esteel) of 200 GPa and coefficient of thermal expansion (a) of 11.7 x 10^-6 /°C. Cross-sectional area: AC: 1960 mm² AD: 1250 mm² Length: AC: √2 meters (square root of 2 meters) AD: 1 meter Inclination angles: AC: θ₁ (theta 1) = 30° from horizontal AD: θ₂ (theta 2) = 20° from horizontal Load on bar AB: Idealized linearly increasing load with a maximum value of 30 kN/m at point B. Problem Objectives: Determine the internal forces (axial forces) acting within bars AC and AD due to the applied load on AB. Calculate the displacement of point A in both horizontal (dA,x) and vertical (dA,y) directions.If the bar is cooled by 10°C, what would be the: Determine the internal forces (axial forces) acting within bars AC and AD…
A 1.0 meter long A36 steel rod with a diameter of 40mm is lightly attached at both end of the rod, end A and end B. A collar is located in the center of the rod. The initial temp is 60 degrees C. The final temperature is 35 degrees C. Determine the force that must be applied to the collar so that the reaction at B is zero.Given:Delta T=25 degrees CE for A36 steel: 200 GPaCoeff of thermal expansion: 12(10^-6)/degree C
# 2-14. Normal Strain in rods constrained by walls with misfit At its initial temperature, the bar is too long by a distance of 8 to fit into the gap between the rigid walls, which are separated by a distance L. In order to make it fit tightly, the bar is cooled to a very low temperature so that it shrinks enough to fit easily into the gap. After it is fit in the gap, the temperature of the bar is raised to a temperature AT below the initial temperature and the bar fits tight between the walls. What is the stress in the bar at this temperature AT? The bar has elastic modulus E = 35. 10³ ksi, thermal expansion coefficient a = 6.10-6 /°F and cross-sectional area A = 1 in². Use L = 10 in, 8 = 3 . 10-² in and AT = -200 °F. 0 = ksi L Initial AT=0 L Final AT
The sinusoidal waveform of an ac circuit shows that the: <-90% O the current is leading the applied voltage by 90 O applied voltage is leading the current by 90 O applied voltage is lagging the current by 90 applied voltage is in phase with the current
The constant a for a steel material having an ultimate strength of 106.5 ksi is
19 This theory explains that the elastic failure occurs when energy per unit volume in a strained material reaches the value of the strain energy per unit volume at the elastic limit point in the simple tension test. Also, the maximum energy which a body can store without deforming plastically is constant for that material irrespective of the manner of loading. What do you call this theory Bulk Modulus Volumetric strain Hook's Law Elastic Theory Strain energy theory
A high-density polyethylene [E = 135 ksi and a = 69 x 10-6/°F) block (1) is positioned in a fixture. The block is 2.1 in, by 2.2 in. by 36 in. long. At room temperature, a gap of 0.1 in. exists between the block and the rigid support at B. Assume L₁- 36 in and A = 0.1 in. Determine: (a) the normal stressa in block (1) caused by a temperature increase of 70°F. (b) the normal strain e in block (1) at the increased temperature. Answers: (a) a = (b) = i B 277.05 A LA psi. pc.