Example 5 118 slug-143 T 0.5 ft 1 ft G /2 ft 10 PROB 106-107 Cucation All Rights Re 0.25 ft 1 ft F=ma Muscs=Slug Determine the moment of inertia of the assembly about an axis that is perpendicular to the screen and passes through the center of mass G. The material has a specific -32.211²2 weight of y = 90 lb/ft³.

Example 5 118 slug-143 T 0.5 ft 1 ft G /2 ft 10 PROB 106-107 Cucation All Rights Re 0.25 ft 1 ft F=ma Muscs=Slug Determine the moment of inertia of the assembly about an axis that is perpendicular to the screen and passes through the center of mass G. The material has a specific -32.211²2 weight of y = 90 lb/ft³.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

if a certain type of steel has a ultimate strength of 185 ksi, calculate the value of constant a(alpha) for the material. choices: a. 0.00438 b 0.000438 c. 0.000348 d. 0.0003438
Aluminum [E = 72 GPa] member ABC supports a load of 31 kN, as shown in the figure. Determine (a) the value of load P such that the deflection of joint C is zero. (b) the corresponding deflection of joint B (positive if B moves up and negative if down). 1.0 m 1.3 m 31 KN C 34-mm diameter B 52-mm diameter
The assembly shown in the figure consists of an aluminum tube AB and a steel rod BC. The rod is attached to the tube through the rigid collar at B and passes through the tube. The cross-sectional area of the rod is 75 mm2 and the cross-sectional area of the tube is 400 + UV in mm2, where UV is 99. A tensile load of 80 kN is applied to the rod. Take Est = 200 GPa for the steel rod, Eal = 70 GPa for the aluminum tube. Determine: (a) the displacement of end C with respect to end B (i.e., the elongation of the steel rod), (b) the displacement of end B with respect to the fixed end A (i.e., the shrink of the aluminum tube), (c) the displacement of the end C of the rod (i.e., (a) + (b)).
Which of the following is not true about the CU test OR-test O Can measure Su quick test O Can measure c' and ' if u is measured
A 1.0 meter long A36 steel rod with a diameter of 40mm is lightly attached at both end of the rod, end A and end B. A collar is located in the center of the rod. The initial temp is 60 degrees C. The final temperature is 35 degrees C. Determine the force that must be applied to the collar so that the reaction at B is zero.Given:Delta T=25 degrees CE for A36 steel: 200 GPaCoeff of thermal expansion: 12(10^-6)/degree C
A machine element in a packaging machine is subjected to a tensile load of 36.6 kN that will be repeated several thousand times over the life of the machine. The cross section of the element is 12 mm thick and 20 mm wide. Specify a suitable material from which to make the element. 47
i need clear ans and solve very very fast in 20 min and thank you DYBALA -8 Discuss the stability and determinacy of the structures shown in Figure (1). m (a) Frame th (c) Frame ifth (d) Composite Figure (1) (b) Truss क (e) Beam
1) The head H is connected to the cylinder of a compressor using six steel bolts. If the clamping force in each bolt is 4000N, determine the normal strain in the bolts. Each bolt has a diameter of 5 mm. If o₂ = 280 MPa and Est = 210GPa, what is the strain in each bolt when the nut is unscrewed so that the clamping force is released? a) 0.970 b) 0.203 c) 0.970(10-³) d) Insufficient information to determine because the stress is beyond yield point H &
Determine the displacement of point A on the free end of the cantilever beam. Neglect the overlap between material 2 and material 3. 2 in- 12 in 6 in 11 ft. 10 in 4 in P = 1000 lbs A PL 3EI Material 1- E₁20,000 ksi Material 2- E₂ = 5,000 ksi Material 3- E₂ 10,000 ksi
21:19 40 A 9 41%- Chegg Home Expert Q&A My answers ( Civil Engineering Question The rope ABexerts a 46 - N force T on the collar at A Let rCA be the position vector from point Cto point A (Figure 1) Figure You answered Bo P1 II
Bar ABC is rigid and rotates freely about B. The loads consist of a point load and a uniform temperature change in both bars CD and EF. Determine the temperature change (AT) at which points A and E first come into contact. Report your answer rounded to the nearest degree. 100 in initial gap = 0.11 in F T E A = 2.0 in² AEF EEF = 12,000 ksi aEF LEF 100 in = 13.5 x 10-6 1/°F = 50 in B 14 k 100 in D с ACD= 1.5 in² ECD CD= 6.5 x 10-6 1/°F = 29,000 ksi = 150 in LCD Y Z
A rigid bar is supported by two copper ro ds and the gap (A) between the aluminu m rod and the bar is 1.50 mm. If the temp erature for all materials is increased by 4 0 degrees Celsius, will the aluminum rod touch the rigid bar or not? Prove your ans wer by stating computed data. Disregard the weight of the rigid bar. For each copper bar, A = 500 mm^2, E = 120 GPa, and a = 1 6.8 μm/(m. C). For the aluminum bar, A = 400 mm^2, E = 70 GPa, and a = 23. 1 μm/(m. C).(* Copper Aluminum Copper 750 mm